Pioneer VSX-9500S VSX-7500S Betriebsanleitung - Seite 28
Blättern Sie online oder laden Sie pdf Betriebsanleitung für Stereo-Empfänger Pioneer VSX-9500S VSX-7500S herunter. Pioneer VSX-9500S VSX-7500S 48 Seiten.
Auch für Pioneer VSX-9500S VSX-7500S: Betriebsanleitung (48 seiten)
Seite drucken
FRONT PANEL FACILITIES
NOTE:
68) ACOUSTIC
Switch
MEMORY:
SELECT
This switch has three functions:
the order shown below.
po
FLAT -® LOUDNESS
-» A
B.C -& D - E 5
mT
FLAT: For flat (normal) frequency response
Ci] LOUDNESS: Emphasizes the low. and high frequency ranges.
Produces a fuller sense of sound.
Car] A-—E: Memorized acoustic memory settings.
© To preset the acoustic memories (AE)
* To recall previously set sound quality settings
Presetting the acoustic memory
@
Adjust the sound quality as desired using the BASS and TREBLE
contro! switches. LOUDNESS or FLAT only, can also be chosen.
™ Settings are shown by the TONE indicator on the display section.
@
Press the ACOUSTIC MEMORY switch
® The TONE indicator on the display section blinks on and off.
@
Press the ACOUSTIC SELECT switch and select the sign to which
you wish to assign the setting (A — E)
™ The sound
quality setting is memorized
approximately
two
seconds after you last press the ACOUSTIC
SELECT switch.
in this way, the desired tone will be preset in one of the five acoustic
memory positions. To preset four other desired tone settings, perform
the same operations.
To recall the memorized tone settings, press the ACOUSTIC SELECT
switch to select the desired memory position. In this way, five different
tone settings can be preset and recalled in the five positions of the
acoustic memory.
@) BASS control switches
Use to adjust the low-frequency level. Press the + switch to increase
low-frequency level, and the - switch to decrease It.
The TONE indicator appears on the display section.
When
both
sides
(+,
-}
of
the
BASS
control
are
pressed
simultaneously,
the base response
will be set to the flat (normal)
condition.
TREBLE control switches
Use to adjust the high-frequency level. Press the + switch to increase
high-frequency level, and the — switch to decrease it
The TONE indicator appears on the display section
When
both
sides
(+.
-—} of the
TREBLE
control
are
pressed
simultaneously,
the treble response
will be set to the flat (normal)
condition
@ TUNING switches
[When tuning]
+ : Performs tuning in ascending frequency order.
~
: Performs tuning in descending frequency order.
28
<ARBI173>
|When inputting station names]
+ + Displays the letters in alphabetical ordor.
— : Disphtys the alphabet in reverse order. Soe page 21 for details,
@
MEMORY
SCAN switch
Operates
when
the INPUT
SELECTOR
is set to TUNER.
Station
frequencies assigned 10 the STATION CALL switches are tuned in, one
after another, beginning with the current station no., for approximately
5 seconds each, The display section SCAN indicator will light. Press
the switch again and the tuner remains tuned in to the station playing
when the switch was pressed the second time.
Station frequencies not assigned station numbers in the memary are
skipped
@) HITS (Hyper Intelligent Tuning System) switch
@ if the HITS
switch is pressed
at the currently displayed station
frequency, the receiver searches up and down the frequency for the
next station (The SEARCH indicator in the display section lights at
this time.) and stops at the first one it finds
If the HITS switch is pressed during STATION NAME input (see page
21), the receiver performs a memory search in order of ascending
station number for memorized stations whose names begin with the
same
letter as the station just mput
* If the HITS switch is pressed during input of numbers for DIRECT
ACCESS tuning, the receiver sets the remaining digits which have
not yet been input to "O'
arches for the corresponding frequencies,
and stops on the first station it finds.
NOTE:
* The system searches for stations within successive 1MHz ranges for
FM and 100 kHz ranges for AM. During DIRECT ACCESS
tuning, it
searches up and down for a station until it reaches the edges of the
band.
If no receivable station is found within the band range, the
receiver returns to the state it was in before the HITS switch was
pressed.
© /f the upper for lower) frequency limit of the receiver is encountered
during HITS operation, the receiver stops searching in that direction
but continues to search in the other.
G2. MEMORY switch
When the unit is in the frequency display mode, pressing this switch
will result in the memorization of the current broadcast band, reception
frequency ACOUSTIC MEMORY position, and FM AUTO/MONO mode.
This switch is also used to input station names (see page 21}.
@
STATION NAME switch
This switch is used when inputting station names (see page 21).
@) AUTO/MANUAL TUNING selector switch
This switch is used to select the tuning mode. The AUTO tuning mode
has been selected when the TUNING AUTO indicator lights.
AUTO tuning
When the — or + TUNING switch is pressed, the receiver automatically
scans the broadcast station frequencies. When a broadcast is detected,
the scanning stops.at that frequency.
NOTE:
Pressing the TUNING switch {— or +} while scanning is taking place
causes scanning to stop.
MANUAL
tuning
This is the usual tuning method. Each time the — or + TUNING switch
is pressed, the reception frequency is changed by one channel step.
When
pressed
continuously,
the
receiver
scans
the
broadcast
frequencies continuously.
@) DIRECT ACCESS TUNING switch
When this switch is pressed, the STATION CALL switches function as
ten-key number
switches
for direct input of the desired reception
frequency.
lf the input station falls outside of the receiver's tuning range, the display
section will display a message: ''UPPER" if the frequency is too high
and "LOWER"
if it is too low.