Pioneer VSX-D3S Gebrauchsanweisung - Seite 11
Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Stereo-Empfänger Pioneer VSX-D3S herunter. Pioneer VSX-D3S 40 Seiten. Audio/video stereo receiver
Auch für Pioneer VSX-D3S: Betriebsanleitung (40 seiten)
Seite drucken
REAR PANEL FACILITIES
Illustration shows Multi-voltage model.
1
2
3
PAL
FM 50kHz
/50 S
AM 9kHz
CHANNEL
/FM DE-
ANTENNA
1 FM/AM ANTENNA terminals
Use these antenna terminals for reception of normal FM and AM
broadcasts.
2 CHANNEL STEP switch
(Multi-voltage model only)
See page 4.
3 PAL/NTSC switch
(Multi-voltage model only)
See page 4.
4 TAPE 2 MONITOR jacks
Connect to audio components such as a second cassette deck or
a graphic equalizer.
5 PHONO input jacks
Connect to the output cables from a turntable.
6 GND terminal
Connect the turntable ground lead to this terminal.
7 VCR 2 jacks
[VIDEO OUT]
Connect to the VCR 2 VIDEO INPUT jack.
[AUDIO OUT (L, R)]
Connect to the VCR 2 AUDIO INPUT jacks.
[VIDEO IN]
Connect to the VCR 2 VIDEO OUTPUT jack.
[AUDIO IN (L, R)]
Connect to the VCR 2 AUDIO OUTPUT jacks.
8 VIDEO OUT (TO MONITOR TV) jack
Connect to a monitor TV or to TV sets with video input terminals
to watch program materials from a VCR or LD player connected
to this unit.
9 CONTROL IN/OUT jacks
IN
: Connect this jack to other Pioneer components when
using those components to control this unit.
OUT : Connect this jack to other Pioneer components when
using the remote control of this unit to control the other
components.
4
6
7
8
9 10
5
CONTROL
VIDEO OUT
GND
TO MONITOR TV
NTSC
MAIN-
IN
REPEATER
PHONO
IN
OUT
100kHz
/75 S
OUT
VCR2
10kHz
REC
STEP
IN
1
EMPHASIS
TAPE2
MINI-
MONI-
REPEATER
TOR
OUT
VCR1
FM
PLAY
OUT
BAL
300
REC
IN
TAPE1
FM
LD
UNBAL
IN
75
PLAY
TV
GND
CD
IN
/SAT
OUT
IN
R
R
L
AM
L
VIDEO
SEE INSTRUCTION MANUAL
LOOP
ANTENA
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING CORPORATION.
"DOLBY","AC-3", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE TRADEMARKS OF
DOLBY LABORATORIES LICENSING CORPORATION.
14
15
16 17 18
19
11 12
SYSTEM CONTROL
SUB WOOFER
IR OUT
PRE
OUT
2
S
I
S
IN
S
IN
SPEAKER
IMPEDANCE
TO
8
16
S
AC-3 •
AC-3 •
MONITOR
R
SPEAKER
TV
DIGITAL IN
RF IN
TV
/SAT
LD
20
21
22
23
Receiver
Remote
control unit
NOTE:
÷ If there is a plug in this unit's CONTROL IN jack, Intelligent
System Control and GUI operation are not possible.
÷ The receiver's remote sensor does not function when a plug is
inserted in the IN jack. To operate, point a remote control unit
other than this unit's supplied remote control unit at the
remote sensor on the component to which the receiver's IN
jack is connected.
÷ You cannot use the supplied remote control unit to operate this
unit via another component's remote sensor.
0 SYSTEM CONTROL IR OUT jacks
To operate other components with this unit's remote control or
with GUI, connect the supplied repeater. (See page 10.)
MINI-REPEATER 1, 2:
Connect the supplied Mini-Repeater.
MAIN-REPEATER:
Connect the supplied Main-Repeater.
- SUB WOOFER PRE OUT jack
When you play back the low frequencies with a sub-woofer,
connect to a powered sub-woofer.
= CENTER PRE OUT jack
Connect when using a PIONEER projection monitor receiver's
built-in speaker as a center speaker.
Refer to the projection monitor's operating instructions for details
concerning connection and operation.
13
TWO VOLTAGE SELECTORS
CENTER
SPEAKER
SELECTOR
PRE
110V
OUT
SPEAKER
120 127V
I+II
IMPEDANCE
8
16
CENTER
SPEAKER
SPEAKERS
CAUTION:
THE POWER
220V
240V
I ONLY
SUPPLY CORD SHOULD
220V
BE DISCONNECTED
120-127V
110V
240V
BEFORE CHANGING
THE VOLTAGE
SELECTOR.
SEE
A
II
INSTRUCTION
MANUAL
R
L
SWITCHED
TOTAL 100W MAX
FRONT
SPEAKERS
L
UNSWITCHED
REAR
100W MAX
SPEAKERS
R
L
B
CAUTION:
SPEAKER IMPEDANCE
DO NOT CONNECT
8
16
SPEAKER
TV SET CR MONITOR.
AC OUTLETS
24
25
26
PIONEER component
bearing the Î mark.
To the CONTROL IN jack of
the PIONEER component
bearing the Î mark.
27
11
<
>
ARB7050