Pioneer D-23 Betriebsanleitung - Seite 13
Blättern Sie online oder laden Sie pdf Betriebsanleitung für Verstärken Pioneer D-23 herunter. Pioneer D-23 16 Seiten. Electronic crossover network
Auch für Pioneer D-23: Betriebsanleitung (21 seiten)
![Pioneer D-23 Betriebsanleitung](/uploads/products/server2/6625450/6625450.png)
- 1. Electronic Crossover
- 2. Operating Instructions
- 3. Table of Contents
- 4. Features
- 5. 3-Way Amplifier Systems
- 6. Multi-Amplifier Systems
- 7. Connection Diagram
- 8. Connections
- 9. Precautions
- 10. Front Panel Facilities
- 11. Before Operating the
- 12. 4-Way Amplifier Systems
- 13. 2-Way Amplifier Systems
- 14. Characteristics Charts
- 15. Specifications
SELECTION OF CROSSOVER FREQUENCIES
BETWEEN LOW MID-RANGE AND HIGH MID
RANGE FREQUENCIES (320Hz-3.2kHz) AND
BETWEEN HIGH MID-RANGE AND HIGH FRE
QUENCIES (1.6kHz-16kHz)
(Connections to MID-LOW, MID-HIGH, and HIGH
Output Terminals)
Connect stereo power amplifiers to the MID-LOW,
MID-HIGH, and HIGH output terminals, as shown
in Fig. 22, and then connect appropriate speakers
to each of the amplifiers. After considering the
characteristics of each speaker combination, select
suitable crossover frequencies and slopes by means
of
the
frequency
selector
controls
(MID-LOW
LP,
HIGH LP, and HIGH HP).
The MID-LOW HP slope selector control must be
set to the FLAT position in this case.
Stereo power amplifier
Output
Input
High
Mid-High
Mid-Low
320Hz�3.2kHz
MID-LOW HP slope selector control set to FLAT position
and
slope
selector
MID-HIGH
HP,
MID
Tweeter
Mid-range
speaker
W oofer
Fig. 22
1.6kHz�l6kHz
Fig. 23
2-WAY AMPLIFIER
SYSTEMS
2-way amplifier systems can be formed in several
different
ways,
depending
selector
controls
are
composition will depend on the individual charac
teristics
of
the
different
Operation of these 2-way systems is the same as
described under "Operational Procedure".
NOTE:
Except where otherwise
controls must NOT be set to the FLAT positions. Failure
to comply with this stipulation may result in damage to
the speakers.
Mid-high
H P
Input
Mid-low
M
id-\OWSiope
HP
��Ptc�or
LP
control
FLAT
Slope
selector
control
Low LP
SELECTION
OF
CROSSOVER
BETWEEN LOW MID-RANGE AND HIGH MID
RANGE FREQUENCIES (320Hz-3.2kHz)
to
(Connections
MID-LOW and MID-HIGH Output
Terminals)
Connect stereo power amplifiers to the MID-LOW
and MID-HIGH
output
Fig. 25, and then connect the appropriate speakers
to the amplifiers. After considering the combined
characteristics of the speaker combination, select a
suitable crossover frequency and slopes by means
of the frequency selector and slope selector con
trols (MID-LOW LP and MID-HIGH HP).
The MID-LOW HP and MID-HIGH L P slope selec
tor controls must be set to FLAT positions in this
case.
Input
Output
Mid-high
Mid-low
on
how
the
slope
used.
The
most
suitable
speakers
employed.
designated,
the slope selector
High
Hig h HP
s1 o o•
Lev el
output
����:gr
Mid-high
Mid-high
�!ffc;or
LP
��?fc;or
output
control
control
FLAT
Mid-low
output
��� � �ig{
FLAT
Low
output
Fig. 24
FREQUENCY
terminals, as shown in
Stereo power amplifier
Tweeter
W oofer
Fig. 25