Pioneer GM-X374 Benutzerhandbuch - Seite 4

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Verstärken Pioneer GM-X374 herunter. Pioneer GM-X374 8 Seiten. Bridgeable four-channel power amplifier

Seite drucken

Installation

CAUTION

Example of installation on the floor

• Do not install in:

mat or on the chassis

—Places where it could injure the driver or pas-

sengers if the vehicle stops suddenly.

—Places where it may interfere with the driver,

1. Place the amplifier where it is to be

such as on the floor in front of the driver's

installed. Insert the supplied tapping

seat.

screws (4 × 18 mm) into the screw

• Make sure that wires are not caught in the sliding

mechanism of the seats, resulting in a short-cir-

holes. Push on the screws with a

cuit.

screwdriver so they make marks

• Confirm that no parts are behind the panel when

where the installation holes are to be

drilling a hole for installation of the amplifier.

Protect all cables and important equipment such

located.

as fuel lines, brake lines and electrical wiring

from damage.

2. Drill 2.5 mm diameter holes at the

• Install tapping screws in such a way that the screw

point marked, and install the ampli-

tip does not touch any wire. This is important to

prevent wires from being cut by vibration of the

fier, either on the carpet or directly

car, which can result in fire.

to the chassis.

• To prevent electric shock, do not install the ampli-

fier in places where it might come in contact with

Tapping-screws

liquids.

(4 × 18 mm)

• To ensure proper installation, use the supplied

parts in the manner specified. If any parts other

than the supplied ones are used, they may damage

internal parts of the amplifier, or they may

become loose causing the amplifier to shut down.

To prevent malfunction

• To ensure proper heat dissipation of the amplifier,

be sure of the following during installation.

—Allow adequate space above the amplifier for

proper ventilation.

—Do not cover the amplifier with a floor mat or

carpet.

Floor mat

• Do not install the amplifier near a door where it

or chassis

may get wet.

• Do not install the amplifier on unstable places

Drill a 2.5 mm diameter hole

such as the spare tire board.

• The best location for installation differs with the

car model and installation location. Secure the

amplifier at a sufficiently rigid location.

• Make temporary connections first and check that

the amplifier and the system operate properly.

• After installing the amplifier, confirm that the

spare tire, jack and tools can be easily removed.

Specifications

GM-X574

Power source .............................................................................................................. 14.4 V DC (10.8 — 15.1 V allowable)

Grounding system ............................................................................................................................................ Negative type

Current consumption ........................................................................................................ 26.5 A (at continuous power, 4 Ω)

Average current drawn* .......................................................................................................... 9.1 A (4 Ω for four channels)

14.2 A (4 Ω for two channels)

Fuse .......................................................................................................................................................................... 25 A × 2

Dimensions ........................................................................................................................ 269 (W) × 50 (H) × 309 (D) mm

Weight ...................................................................................................................... 3.7 kg (Leads for wiring not included)

Maximum power output .................................................................................................................... 100 W × 4 / 260 W × 2

Continuous power output .......................................................... 50 W × 4 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.15% THD)

130 W × 2 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.8% THD)

65 W × 4 (at 14.4 V, 2 Ω, 20 — 20,000 Hz, 0.8% THD)

Load impedance ............................................................................................................................ 4 Ω (2 — 8 Ω allowable)

(Bridge connection: 4 — 8 Ω allowable)

Frequency response ............................................................................................................ 10 — 45,000 Hz (+0 dB, –1 dB)

Signal-to-noise ratio .......................................................................................................................... 97 dB (IEC-A network)

Distortion ............................................................................................................................................ 0.008% (10 W, 1 kHz)

Separation ........................................................................................................................................................ 65 dB (1 kHz)

Low pass filter ................................................................................................................................ Cut off frequency: 80 Hz

Cut off slope: –12 dB/oct

High pass filter ................................................................................................................................ Cut off frequency: 80 Hz

Cut off slope: –12 dB/oct

Maximum input level/impedance .................................................................................... RCA: 6.5 V/22 kΩ (0.2 — 6.5 V)

Speaker: 26 V/40 kΩ (0.8 — 26 V)

Note:

• Specifications and the design are subject to possible modification without notice

due to improvements.

*Average current drawn

• The average current drawn is nearly the maximum current drawn by this unit

when an audio signal is input. Use this value when working out total current

drawn by multiple power amplifiers.

GM-X374

Power source .............................................................................................................. 14.4 V DC (10.8 — 15.1 V allowable)

Grounding system ............................................................................................................................................ Negative type

Current consumption ........................................................................................................ 19.2 A (at continuous power, 4 Ω)

Average current drawn* .......................................................................................................... 6.7 A (4 Ω for four channels)

10.9 A (4 Ω for two channels)

Fuse .................................................................................................................................................................................. 30 A

Dimensions ........................................................................................................................ 265 (W) × 50 (H) × 237 (D) mm

Weight ...................................................................................................................... 2.8 kg (Leads for wiring not included)

Maximum power output ...................................................................................................................... 70 W × 4 / 200 W × 2

Continuous power output .......................................................... 35 W × 4 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.08% THD)

100 W × 2 (at 14.4 V, 4 Ω, 20 — 20,000 Hz, 0.8% THD)

50 W × 4 (at 14.4 V, 2 Ω, 20 — 20,000 Hz, 0.8% THD)

Load impedance ............................................................................................................................ 4 Ω (2 — 8 Ω allowable)

(Bridge connection: 4 — 8 Ω allowable)

Frequency response ............................................................................................................ 10 — 45,000 Hz (+0 dB, –1 dB)

Signal-to-noise ratio ...................................................................................................................... 100 dB (IEC-A network)

Distortion ............................................................................................................................................ 0.008% (10 W, 1 kHz)

Separation ........................................................................................................................................................ 65 dB (1 kHz)

Low pass filter ................................................................................................................................ Cut off frequency: 80 Hz

Cut off slope: –12 dB/oct

High pass filter ................................................................................................................................ Cut off frequency: 80 Hz

Cut off slope: –12 dB/oct

Maximum input level/impedance .................................................................................... RCA: 6.5 V/22 kΩ (0.2 — 6.5 V)

Speaker: 26 V/40 kΩ (0.8 — 26 V)

Note:

• Specifications and the design are subject to possible modification without notice

due to improvements.

*Average current drawn

• The average current drawn is nearly the maximum current drawn by this unit

when an audio signal is input. Use this value when working out total current

drawn by multiple power amplifiers.