Pioneer PRS D3000SPL Benutzerhandbuch - Seite 3

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Verstärken Pioneer PRS D3000SPL herunter. Pioneer PRS D3000SPL 8 Seiten. Class d mono amplifier

Seite drucken

Connecting the Unit

Connecting the Power Terminal

2. Expose the end of the battery wire

and ground wire using nippers or a

• Always use the recommended battery and ground

cutter by about 15–20 mm (5/8–3/4

wire, which is sold separately. Connect the battery

in.) and twist.

wire directly to the car battery positive terminal

(+) and the ground wire to the car body.

• Recommended wires size (AWG: American Wire

Gauge) is as follows. The battery wire, the ground

wire and the optional direct ground wire must be

same size.

15–20 mm

(5/8–3/4 in.)

Battery Wire and Ground Wire Size

3. Connect the wires to the terminal.

Wire Length less than 4 ft

4—7 ft

7—10 ft

• Before connecting the wires to the terminals,

less than 1.2 m 1.2—2.1 m

2.1—3.0 m

remove the endcap. After connecting the

Wire Size

6 AWG

wires to the terminals, attach the endcap.

• Fix the wires securely with the terminal

10—13 ft

13—16 ft

16—19 ft

19—22 ft

screws.

3.0—3.9 m

3.9—4.8 m

4.8—5.7 m

5.7—6.7 m

System remote

6 AWG

4 AWG

control terminal

1. Pass the battery wire from the

GND terminal

engine compartment to the interior

System remote

of the vehicle.

control wire

• After making all other connections to the

amplifier, connect the battery wire terminal of

the amplifier to the positive (+) terminal of

Ground wire

the battery.

Battery wire

The maximum length of the wire between

the fuse and the positive (+) terminal of the

battery is 45 cm (18 in.).

WARNING

Engine

Interior of

Failure to securely fasten the battery wire to the ter-

the vehicle

minal using the terminal screws could cause the ter-

compartment

minal area to overheat and could result in damage

and injury including minor burns.

Fuse 100 A

4. Put the wire ties in the slits and

Drill a 14

Positive (+)

Each amplifier must

mm (1/2 in.)

terminal

wrap the wire ties around the wires.

be SEPARATELY

hole into the

fused at 100 A.

• Wrap the wire tie around the wire insulation,

vehicle body.

not the stripped wire.

Slit

Insert the O-ring rubber

grommet into the vehicle

body.

Wire tie

Connecting the Speaker Terminals

1. Expose the end of the speaker wires

using nippers or a cutter by about

Twist

10 mm (3/8 in.) and twist.

Twist

10 mm

(3/8 in.)

2. Attach lugs to speaker wire ends.

Lugs not supplied.

• Use pliers, etc., to crimp lugs to wires.

Lug

Speaker wire

Endcap

3. Connect the speaker wires to the

speaker terminals.

Terminal

screw

• Fix the speaker wires securely with the termi-

nal screws.

Power

terminal

Terminal screw

Speaker

terminal

Speaker wire

Setting the Gain for

Advanced Setup of the Gain

Synced Amplifier

Starting with the master amplifier, adjust the gain

control on each amplifier in order.

After connecting the speaker wires, adjust each

1. Output sin wave through this system at low output

synced amplifier's gain control. All synced ampli-

level.

fiers follow the master amplifier's settings.

2. Use volt meter to measure the master amplifier's

output voltage level.

3. Use volt meter to measure the synced amplifier's

Quick Setup of the Gain

output voltage level.

4. Match the synced amplifier's output to the mas-

Set each synced amplifier's gain control to the NOR-

ter's output using the gain control on the synced

MAL position. This setting will balance output vol-

amplifier.

umes sufficiently for most applications.

5. Repeat for the each synced amplifier in the proper

order.

Connecting the Speaker Wires

Connect the speaker leads to suit the configuration according to the figures shown below and the next page.

Single Amplifier

• Speaker wire size must be 12 AWG minimum.

• Load may be any combination of speakers but impedance must be 2 Ω or larger.

MODE SELECT switch must be in

Connect to a car stereo.

MASTER position.

For details, see the "Connection Diagram" section.

2 Ω

minimum

1,000 W

Two Amplifier Bridged

• Speaker wire size must be 12 AWG minimum.

• Load may be any combination of speakers but impedance must be 4 Ω or larger.

Connect to a car stereo.

MODE SELECT switch

must be in MASTER position.

For details, see the "Connection Diagram" section.

Connecting wire with

RCA pin plugs (sold

separately).

MODE SELECT switch

must be in SYNC INV

Connecting speaker

position. Before setting

wire (sold separately).

to the position, remove

the screw and the stop-

per.

Two Amplifier

• Speaker wire size must be 12 AWG minimum.

• Load may be any combination of speakers but impedance must be 2 Ω or larger.

MODE SELECT switch

Connect to a car stereo.

must be in MASTER position.

For details, see the "Connection Diagram" section.

Connecting wire with

RCA pin plugs (sold

separately).

MODE SELECT

switch must be in

SYNC position.

4 Ω

minimum

2,000 W

2 Ω

minimum

1,000 W

2 Ω

minimum

1,000 W