Pioneer CDJ-1000MKII Betriebsanleitung - Seite 11

Blättern Sie online oder laden Sie pdf Betriebsanleitung für CD-Spieler Pioneer CDJ-1000MKII herunter. Pioneer CDJ-1000MKII 20 Seiten. Compact disc player

Seite drucken

DISC LOADING/UNLOADING

Label surface up

1. Set the rear-panel POWER switch to ON.

Do not force a disc into the unit when the POWER switch is set to OFF

as this may damage the disc and the unit.

2. Insert a disc.

¶ Hold the disc with label surface upwards, and insert into the front panel

disc loading slot .

¶ When playing 8cm discs, be sure to install an adaptor.

This unit spins at high speed to provide high performance. When

playing 8cm discs with an adaptor, for safety reasons the rotation

speed is reduced as a result scratch and reverse speeds will be lower.

¶ Only one disc can be loaded at a time. Never attempt to load more than one

disc at the same time, or attempt to load a second disc when one disc has

already been loaded.

¶ When loading a disc, do not placing any twisting force on the disc, or try to

force the disc into the slot. Also, do not attempt to interrupt or defeat the

motion of the disc when the player begins to draw a disc into the slot or to

eject a disc, since damage to the disc or player could occur.

DJ PLAYER OPERATION

WAVE SEARCH(ZOOM)

2, 3

TIME MODE

/ AUTO CUE

TRACK

4, ¢

1, ¡

CUE

PLAY/PAUSE

Jog dial

Auto Cueing (*)

When a disc is loaded, when track search is performed, and when the track is changed

with the JOG MODE set to CDJ, this function operates to automatically set the

cue point immediately before the actual start of music.

¶ Turning auto cueing on and off

Pressing the TIME MODE/AUTO CUE button and holding it down for a

second or more causes auto cueing to be alternately turned on and off.

When AUTO CUE is on, the [A. CUE] indicator will be lit up.

Insert straight

EJECT UNLOCK/LOCK

EJECT

P. 12

3. The disc can be ejected anytime using the EJECT button (0)

when the EJECT UNLOCK/LOCK switch is set to UNLOCK.

When the EJECT UNLOCK/LOCK switch is set to LOCK,

press the PLAY/PAUSE button (6) during playback, or

when a Cue point has been set, press the CUE button

(back cue) before pressing the EJECT button (0) to

eject the disc.

¶ When the EJECT button is pressed, disc rotation stops and the disc is ejected

from the loading slot.

¶ If the disc cannot be ejected with the EJECT button, insert a pin in the

forced ejection hole on the front panel of the player.

CAUTION:

Do not attempt to press a disc back into the slot when the [EJECT]

indicator appears. Pressing a disc back into the slot while the [EJECT]

indicator appears may cause the player to stop. In this case, press the

EJECT button again and wait until the [EJECT] indicator goes out be-

fore reinserting the disc.

PRECAUTIONS ON PLAYING CD SINGLES (8 cm/3-inch Discs)

1 When playing CD singles (8 cm/3-inch discs), always use the adapter for 8

cm/3-inch discs. Before loading the disc into the CD player, be sure to check

that it is secured properly by the catches of the adapter. If discs have been

inserted without the adapter by mistake, remove the disc immediately by

pressing the EJECT button. If the disc does not come out with one press,

press another time.

2 Use 8 cm/3-inch disc adapters labeled with the

standard product). Do not use adapters which cause the disc to idle, nor

adapters which are bent or curved.

Functions indicated with an asterisk (*) are disabled when

the rear panel DIGITAL OUT mode switch is set to NORMAL.

¶ AUTO CUE on/off status is stored in memory and persists even when the

power is turned off.

¶ It can change the Auto Cue level.

7 Changing the Auto Cue level

1. Press the TIME MODE/AUTO CUE button for over 5

seconds.

¶ The display will indicate [A.CUE-60dB] (in the original state).

2. By -pressing the WAVE SEARCH (ZOOM) button (2, 3)

you can change the level.

¶ It can choose from -36dB, -42dB, -48dB, -54dB, -60dB, -66dB, -72dB and

-78dB.

¶ The level change mode can be removed if you press the TIME MODE/

AUTO CUE button.

¶ Even if you turn the power off, the set level will remain in memory.

Starting Playback

1. Insert a disc in the player.

This unit spins discs at high speeds to provide high performance. As a result,

disc loading takes a couple of seconds.

2. If auto cueing is on, press the PLAY/PAUSE button (3/8).

¶ Press the PLAY/PAUSE button only after the current time lights in the

display. The silent portion at the beginning of the displayed track will be

skipped and playback will begin instantaneously from the first bars of the

track.

Once the first track has been played, the player will automatically search for

the beginning of the next track to be played. The cueing indicator [CUE] will

light up, the PLAY/PAUSE button [3/8] indicator will flash, and the player

will then wait for the PLAY/PAUSE button (3/8) to be pressed before begin-

ning playback of the next track.

BASIC OPERATION

P. 5

mark (recommended