Aeotec MultiSensor Einbauanleitung - Seite 2

Blättern Sie online oder laden Sie pdf Einbauanleitung für Zubehör Aeotec MultiSensor herunter. Aeotec MultiSensor 3 Seiten. Z-wave 4-in-1 sensor: motion, temperature, humidity, and light sensor
Auch für Aeotec MultiSensor: Benutzerhandbuch (10 seiten)

Seite drucken

Z-Wave Network Instructions:

The Aeotec MultiSensor must be paired (included) into a

Z-Wave network before it can send Basic Set Command,

Temperature, Humidity, and Light level reports to

association group 1, which is setup via the Association

Command class. The MultiSensor can only communicate

to devices within its own Z-Wave network.

Note: The LED on the MultiSensor will blink if it is currently

not paired into a Z-Wave network when pressing the

Z-Wave Button.

Adding/Including/Pairing the MultiSensor into a

Z-Wave Network

Press the button labeled "Include" on

the Aeotec Minimote to begin the

Z-Wave inclusion process.

Include

Note: To include the MultiSensor with other controllers, please

consult the operation manual for these controllers on how to

include Z-Wave products into an existing network.

Press the Z-Wave Button under the Battery Cover to begin the

Z-Wave pairing process.

Z-Wave Button

Sensitivity

AAA

Troubleshooting:

If the MultiSensor was not successfully paired

into any Z-Wave network, the MultiSensor's LED will blink when

pressing the Z-Wave Button. If the MultiSensor was successfully

paired into a Z-Wave network, the LED will stay solid for a few

seconds when pressing the Z-Wave Button.

Removing/Resetting the MultiSensor from your

Z-Wave Network

Press the button labeled "Remove" on

the Aeotec Minimote to begin the

Z-Wave removal process.

Remove

Note: To remove the MultiSensor from other controllers,

please consult the operation manual for these controllers

on how to remove Z-Wave products from an existing

network.

Troubleshooting:

If the MultiSensor was successfully removed

from the Z-Wave network, pressing the Z-Wave Button will cause the

LED to blink. If the MultiSensor was not successfully removed from

the Z-Wave network the LED will stay solid for a few seconds.

Monitoring Motion

The MultiSensor can send Basic Set Command to association group 1,

which is setup via the Association Command Class, when the Motion

Sensor detects movement to control the associated devices to "OPEN"

state. After 4 minutes by default, if the Motion Sensor is not triggered

again, the MultiSensor will send Basic Set Command to these devices to

set them to their "CLOSE" state. However, if the Motion Sensor is

triggered again in 4 minutes, the MultiSensor will reset the timing and

start timing again.

The 4 minutes delay time can be changed through the usage of Z-Wave

command built into Z-Wave certified controllers/gateways. (The specific

Z-Wave command supporting this function is Configuration Command

Class) Please consult the operation manual for these controllers /

gateways for specific instructions on setting the MultiSensor.

Monitoring Temperature, Humidity and Luminance

The MultiSensor can report temperature, humidity, and luminance to

a Z-Wave gateway or controller when requested. If this function is

supported by the gateway/controller, the data will be displayed in the

user interface of the gateway/controller.

(The specific Z-Wave

command supporting the monitoring is the Multilevel Sensor

Command Class and Multi Channel Command Class. Automatic

reports are sent to association group 1, which is setup via the

Association Command Class.) Please consult the operation manual

for these gateways/controllers for specific instructions on setting the

MultiSensor.

Warranty

Aeon Labs warrants to the original purchaser of Products that for the

Warranty Period (as defined below), the Products will be free from

material defects in materials and workmanship. The foregoing warranty

is subject to the proper installation, operation and maintenance of the

Products in accordance with installation instructions and the operating

manual supplied to Customer. Warranty claims must be made by

Customer in writing within thirty (30) days of the manifestation of a

problem. Aeon Labs' sole obligation under the foregoing warranty is, at

Aeon Labs' option, to repair, replace or correct any such defect that was

present at the time of delivery, or to remove the Products and to refund

the purchase price to Customer.

The "Warranty Period" begins on the date the Products is delivered and

continues for 12 months.

Any repairs under this warranty must be conducted by an authorized

Aeon Labs service representative and under Aeon Labs' RMA policy.

Any repairs conducted by unauthorized persons shall void this warranty.

Excluded from the warranty are problems due to accidents, acts of God,

civil or military authority, civil disturbance, war, strikes, fires, other

catastrophes, misuse, misapplication, storage damage, negligence,

electrical power problems, or modification to the Products or its

components.

Aeon Labs does not authorize any person or party to assume or create

for it any other obligation or liability in connection with the Products

except as set forth herein.

Aeon Labs will pass on to Customer all manufacturers' Material

warranties to the extent that they are transferable, but will not

independently warrant any Material.

Customer must prepay shipping and transportation charges for returned

Products, and insure the shipment or accept the risk of loss or damage

during such shipment and transportation. Aeon Labs will ship the

repaired or replacement products to Customer freight prepaid.

Customer shall indemnify, defend, and hold Aeon Labs and Aeon Labs'

affiliates, shareholders, directors, officers, employees, contractors,

agents and other representatives harmless from all demands, claims,

actions, causes of action, proceedings, suits, assessments, losses,

damages, liabilities, settlements, judgments, fines, penalties, interest,

costs and expenses (including fees and disbursements of counsel) of

every kind (i) based upon personal injury or death or injury to property to

the extent any of the foregoing is proximately caused either by a

defective product (including strict liability in tort) or by the negligent or

willful acts or omissions of Customer or its officers, employees,

subcontractors or agents, and/or (ii) arising from or relating to any actual

or alleged infringement or misappropriation of any patent, trademark,

mask work, copyright, trade secret or any actual or alleged violation of

any other intellectual property rights arising from or in connection with

the products, except to the extent that such infringement exists as a

result of Aeon Labs' manufacturing processes.

IN NO EVENT SHALL AEON LABS BE LIABLE FOR ANY INDIRECT,

INCIDENTAL,

PUNITIVE,

SPECIAL

CONSEQUENTIAL

DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, OR

USE INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHETHER

IN AN ACTION IN CONTRACT, OR TORT, OR OTHERWISE EVEN IF

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. AEON LABS'

LIABILITY AND CUSTOMER'S EXCLUSIVE REMEDY FOR ANY

CAUSE OF ACTION ARISING IN CONNECTION WITH THIS

AGREEMENT OR THE SALE OR USE OF THE PRODUCTS,

WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY, BREACH

OF WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE

PRINCIPLES, IS EXPRESSLY LIMITED TO, AT AEOTEC'S OPTION,

REPLACEMENT OF, OR REPAYMENT OF THE PURCHASE PRICE

FOR THAT PORTION OF PRODUCTS WITH RESPECT TO WHICH

DAMAGES ARE CLAIMED. ALL CLAIMS OF ANY KIND ARISING IN

CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF

PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN

WRITING WITHIN THIRTY (30) DAYS FROM AEON LABS' DELIVERY,

OR THE DATE FIXED FOR DELIVERY IN THE EVENT OF

NONDELIVERY.

THE INDEMNITY AND WARRANTY IN ABOVE ARE EXCLUSIVE AND

IN LIEU OF ALL OTHER INDEMNITIES OR WARRANTIES, WHETHER

EXPRESS OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE.

FCC NOTICE (for USA):

THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR

TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS

TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE

USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY

LOCATIONS. DO NOT IMMERSE IN WATER. NOT FOR USE WHERE

DIRECTLY EXPOSED TO WATER.

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

1. This device may not cause harmful interference, and

2.This device must accept any interference received, including

interference that may cause undesired operation. This equipment has

been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with

the

instructions,

may

cause

harmful

interference

communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following

measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Warning:

Do not dispose of electrical appliances as unsorted municipal waste,

use separate collection facilities.

Contact your local government for information regarding the collection

systems available.

Certifications (regional):

Do not dispose of electrical appliances as unsorted municipal waste,

use separate collection facilities.

Contact your local government for information regarding the collection

systems available.

radio