Aeotec ZW089 Handbuch

Blättern Sie online oder laden Sie pdf Handbuch für Zubehör Aeotec ZW089 herunter. Aeotec ZW089 2 Seiten. Recessed door sensor gen5

Seite drucken

Aeotec by Aeon Labs Recessed Door

The Magnetic Sensor

Sensor Gen5.

From Aeotec by Aeon Labs' intelligence series

and our Gen5 range, comes Recessed Door

Sensor. Invisibly installed, it sits within a door

and its frame to provide all the information

needed by a Z-Wave

system for security,

safety and ambiance without altering a room's

aesthetics.

The installation of your Recessed Door Sensor

Familiarize yourself with your

has two key steps:

Recessed Door Sensor Gen5.

1. Install both parts of your sensor.

Your Recessed Door Sensor is comprised

2. Connect your sensor to your Z-Wave network.

View the expanded manual:

of two parts: the larger Main Sensor and the

http://aeotec.com/support

Prepare the Main Sensor.

smaller Magnetic Sensor.

1. Using a slot-head screw driver, remove the

Main Sensor's lid by pressing gently against its

The larger Main Sensor

exposed connector.

LE D

Screw Hol e

Main

Sensor

Z- Wave Button Hole

2.Separate the Main Sensor's two sections

by first removing its lid and then removing its

internal components.

Magnetic

Sensor

A magnet in th e plastic shell

3.Remove the clear battery insulator by pulling

Quick start.

it away from the Main Sensor.

4.With the battery insulator removed, reinsert

the internal components into the Main Sensor's

enclosure before reattaching its lid. Ensure that

the Main Sensor's button aligns with the button

hole of its lid. The Main Sensor will now look as

it did prior to step 1.

Install your Recessed Door Sensor.

The rectangular areas highlighted above are

optimal installation positions.

With the Main Sensor powered and activated, it

is now time to inlay it within your selected door

Step 1

frame.

Prepare a space for the Main Sensor by drilling

Before beginning it is important to select a

a hole into your doorframe using a 19mm wide

suitable position for your Recessed Door

drill bit. The hole should be 65mm deep.

Sensor. For optimal performance, your sensor

should be:

65mm deep

19mm

1. Either installed at the top of a door or the

side of a door.

2. Positioned away from metal that could

interfere with its magnetic functionality. This

Doorframe

Drill bit

includes your door's plate, handle or lock

mechanism.

3. Installed in a suitable location to ensure a

Step 2

clear (between 1mm and 5mm) separation

Drill a corresponding hole in your door. The

when the door is closed.

hole should be 15mm deep. As stated, the

4. Positioned exactly above or beside the

position of this hole should align exactly with

position in which the Magnetic Sensor will be

the hole you just created in the doorframe.

inlayed.

Again, use a 19mm wide drill bit.

Top of the doo r

Side of the doo r

15mm deep

19mm

Door

Dril l bi t

Step 5

With your door and doorframe prepared and

the drill holes created, it's now time to mount

The gap between the two parts of your sensor

both parts of your Recessed Door Sensor.

must be no less than 1mm and no more than

5mm. If your gap is different, re-affix the Main

Step 3

Sensor by altering its hole.

Insert the Main Sensor into the hole you created

Magnetic

in the door frame then secure it using two screws.

Sensor

1m m

Main Sensor

Magnetic

Sensor

Main Sensor

Secure wit h screws

Done

Add your sensor to your Z-Wave network.

Step 4

With your Recessed Door Sensor installed

Place a small amount of white glue (PVA)

within a door and its frame, it's time to add

inside the hole you created for the Magnetic

it to your Z-Wave network. The following

Sensor. Then place the sensor over and into

instructions tell you how to do this using

the hole. Next, insert it by tapping gently on it

Aeotec's Z-Stick and Minimote controllers. If

with a rubber hammer.

you are using other products as your main

Z-Wave controller, please refer to the part of

their respective manuals that tell you how to

add new devices to your network.

If you're using a Z-Stick:

Tap with

hammer

Done

1. Take your Minimote to the door in which your

Action Button

Recessed Door Sensor has been installed.

2. Press the Include button on your Minimote.

3. Press the Z-Wave Button on your sensor

with a small pin or toothpick.

4. If your Recessed Door Sensor had been

1. If your Z-Stick is plugged into a gateway or a

successfully linked to your network, its LED

computer, unplug it.

light will remain illuminated for 10 minutes. If

2. Take your Z-Stick to the door in which your

the linking was unsuccessful, its LED light

Recessed Door Sensor has been installed.

will blink for 3 seconds before turning off.

3. Press the Action Button on your Z-Stick.

5. Press any button on your Minimote to take it

4. Press the Z-Wave Button on your sensor with

out of installation mode.

a small pin or toothpick.

5. If your Recessed Door Sensor had been

successfully linked to your network, its LED

light will remain illuminated for 10 minutes. If

Advanced.

the linking was unsuccessful, its LED light

Remove your sensor from your Z-Wave

will blink for 3 seconds before turning off.

network.

6. Press the Action Button on the Z-Stick to take

Your Recessed Door Sensor can be removed

it out of installation mode.

from your Z-Wave network at any time. You'll

need to use your Z-Wave network's main

If you're using a Minimote:

controller to do this. The following instructions

tell you how to do this using Aeotec by Aeon

Labs' Z-Stick and Minimote controllers. If you

are using other products as your main Z-Wave

controller, please refer to the part of their

respective manuals that tell you how to remove

Include

devices from your network.