Ariston 7 Chefs FO 87 C.2/E TD IX Handbuch für Installation und Gebrauch - Seite 12

Blättern Sie online oder laden Sie pdf Handbuch für Installation und Gebrauch für Backofen Ariston 7 Chefs FO 87 C.2/E TD IX herunter. Ariston 7 Chefs FO 87 C.2/E TD IX 14 Seiten. New oven “7 chefs”
Auch für Ariston 7 Chefs FO 87 C.2/E TD IX: Handbuch für Installation und Gebrauch (14 seiten)

Ariston 7 Chefs FO 87 C.2/E TD IX Handbuch für Installation und Gebrauch
Fitting on a Power Supply Cable
Opening the terminal board:
Using a screwdriver, prise on the side tabs of the ter-
minal board cover;
Pull open the cover of the terminal board.
To install the cable, proceed as follows:
Remove the wire clamp screw and the three contact
screws L-N-
Fasten the wires beneath the screwheads using the
following colour scheme: Blue (N) Brown (L) Yellow-
Green
Fasten the supply cable in place with the clamp and
close the cover of the terminal board.
Connecting the supply cable to the mains
Install a standardised plug corresponding to the load indi-
cated on the data plate. When connecting the cable di-
rectly to the mains, install an omnipolar circuit-breaker with
a minimum contact opening of 3 mm between the appli-
ance and the mains. The omnipolar circuit breaker should
be sized according to the load and should comply with
current regulations (the earth wire should not be inter-
rupted by the circuit breaker).
Inner dimensions of the oven:
Inner Volume of the Oven:
ENERGY LABEL
Directive 2002/40/EC on the label of electric ovens
Norm EN 50304
Energy consumption for Natural convection
Declared energy consumption for Forced convection Class
N
L

Technical Specifications

Width 43.5 cm
Depth 40 cm
Height 32 cm
56 litres
heating mode:
Convection
heating mode:
Baking
The supply cable should be positioned so that it does not
reach a temperature of more than 50°C with respect to
the room temperature, anywhere along its length.
Before making the connection, check that:
The electrical safety of this appliance can only be guar-
anteed if the cooker is correctly and efficiently earthed,
in compliance with regulations on electrical safety. Al-
ways ensure that the earthing is efficient; if you have
any doubts call in a qualified technician to check the
system. The manufacturer declines all responsibility
for damage resulting from a system which has not been
earthed.
Before plugging the appliance into the mains, check
that the specifications indicated on the date plate (on
the appliance and/or packaging) correspond to those
of the electrical mains system of your home.
Check that the electrical capacity of the system and
sockets will support the maximum power of the appli-
ance, as indicated on the data plate. If you have any
doubts, call in a qualified technician.
If the socket and appliance plug are not compatible,
have the socket replaced with a suitable model by a
qualified technician. The latter, in particular, will also
have to ensure that the cross section of the socket
cables are suitable for the power absorbed by the ap-
pliance. The use of adapters, multiple sockets and/or
extensions, is not recommended. If their use cannot
be avoided, remember to use only single or multiple
adapters and extensions which comply with current
safety regulations. In these cases, never exceed the
maximum current capacity indicated on the single
adapter or extension and the maximum power indicated
on the multiple adapter. The plug and socket must
be easily accessible.
Voltage and Frequency of Power Supply:
This appliance conforms with the following
European Economic Community directives:
-
73/23/EEC of 19/02/73 (Low Voltage) and subsequent
modifications;
-
89/336/EEC of 03/05/89 (Electromagnetic
Compatibility) and subsequent modifications;
-
93/68/EEC of 22/07/93 and subsequent
modifications.
23
230V ~ 50Hz 2800W