Whirlpool 2DLSQ7533JQ4 Einbauanleitung - Seite 3

Blättern Sie online oder laden Sie pdf Einbauanleitung für Waschmaschine Whirlpool 2DLSQ7533JQ4 herunter. Whirlpool 2DLSQ7533JQ4 5 Seiten.

Seite drucken

Electrical requirements

WARNING
Electrical Shock Hazard
Plug into a grounded 3-prong
outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these
instructions can result in
death, fire, or electrical shock.
Recommended ground method
3-prong
ground-
type outlet
3-prong
ground
plug
ground
prong
power
supply
cord
Now start...
WARNING
Excessive Weight Hazard
Use two or more people to move
and install washer.
Failure to do so can result in back
or other injury.
A
Preparation:

Inlet hose

B
connection:
(to washer)
Panel B
If codes permit and a separate
ground wire is used, it is
recommended that a qualified
electrician determine that the
ground path is adequate.
Do Not ground to a gas pipe.
Check with a qualified electrician if
you are not sure the washer is
properly grounded.
Do Not have a fuse in the neutral or
ground circuit.
A 120-volt, 50-Hz, Ac-only, 15- or
20-ampere, fused electrical supply is
required. Time-delay fuse or circuit
breaker is recommended. It is
recommended that a separate circuit
serving only this appliance be provided.
For your personal safety, this washer must be
grounded. This washer is equipped with a
power supply cord having a 3-prong ground
plug.
To minimize possible shock hazard,
the cord must be plugged into a mating, 3-
prong, ground-type outlet, grounded in
accordance with local codes and ordinances.
If a mating outlet is not available, it is the
personal responsibility and obligation of the
customer to have the properly grounded
outlet installed by a qualified electrician.
With washer in laundry area.
SLIDE WASHER ONTO CARDBOARD OR
HARDBOARD BEFORE MOVING ACROSS
FLOOR.
Move washer close to its final
location.
shipping
strap
1.
Read, then remove label
that covers power supply cord.
Use new hoses and washers that came with your washer.
Check inlet hoses periodically.
Replace inlet hoses if you find
bulges, kinks, cuts, wear or leaking.
Replace inlet hoses after five years
of use.
GROUNDING INSTRUCTIONS
For a grounded, cord-connected washer:
This washer must be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electrical shock by
providing a path of least resistance for electric current. This washer is
equipped with a cord having an equipment-grounding conductor and
grounding plug. The plug must be plugged into an appropriate outlet
that is properly installed and grounded in accordance with all local
codes and ordinances.
WARNING: Improper connection of the equipment grounding
conductor can result in a risk of electric shock. Check with a qualified
electrician or serviceman if you are in doubt as to whether the
appliance is properly grounded.
Do not modify the plug provided with the appliance – if it will not fit
the outlet, have a proper outlet installed by a qualified electrician.
For a permanently connected washer:
This washer must be connected to a grounded metal, permanent
wiring system, or an equipment grounding conductor must be run
with the circuit conductors and connected to the equipment-
grounding terminal or lead on the appliance.
Remove yellow shipping strap.
Pull the yellow shipping strap
completely out of the washer.
2.
Pull yellow shipping strap with two cotter pins
label
entirely out of washer. The power supply cord
will still be attached to shipping strap.
3.
Pull firmly to remove the
other end of shipping
strap from the back of the
washer to release self-leveling
legs.
Save the shipping strap for use in
Step 17.
coupling
4.
Insert a flat washer into each
end of the inlet hoses. Check
that washers are firmly seated in
couplings.
2 cotter pins
Inlets are plastic.
Do Not strip or
cold water
washer
inlet valve
hot water
inlet valve
5.
Attach one hose to the hot
water (bottom) inlet valve first;
then other hose to the cold water
(top) inlet valve. Tighten couplings
by hand. Then use pliers to make an
additional two-thirds turn.
DO NOT OVERTIGHTEN; this could
cause damage to couplings.
crossthread.