Whirlpool 3RLSQ8533 Einbauanleitung - Seite 3

Blättern Sie online oder laden Sie pdf Einbauanleitung für Waschmaschine Whirlpool 3RLSQ8533 herunter. Whirlpool 3RLSQ8533 5 Seiten. Two speed automatic washer
Auch für Whirlpool 3RLSQ8533: Handbuch für Gebrauch und Pflege (11 seiten), Handbuch für Gebrauch und Pflege (12 seiten)

Seite drucken

Drain system

Untape and open washer lid. Remove packages and hoses from washer. Follow

directions for your type of drain system.

If a longer drain hose is needed, use drain hose extension kit (Part No. 285702).

If drain hose must be shortened, use drain hose kit (Part No. 285442).

All kits are available from authorized parts distributors.

Select the drain hose installation method you need.

If your home has:

99 cm (39") to 183 cm (72'') high,

5,1 cm (2") dia. standpipe

2,5 cm (1")

standpipe

floor drain

overhead sewer

standard 76 liters (20 gal.),

86 cm (34") high drain tub or

utility sink

water not close by

Requirements

WARNING

Electrical Shock Hazard

Plug into an earthed outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to do so can result in death, fire, or

electrical shock.

Installation

Steps

WARNING

Excessive Weight Hazard

Use two or more people to move and install

washer.

Failure to do so can result in back or other

injury.

Inlet hose connection

Check inlet hoses periodically. Replace inlet hoses if you

find bulges, kinks, cuts, wear or leaking. Replace inlet

hoses after five years of use.

Panel B

You will need to buy:

nothing

5,1 cm (2") dia. to 2,5 cm (1") dia.

standpipe adapter, Part No. 3363920

siphon break, Part No. 285320; additional

drain hose, Part No. 3357090;

and Connector Kit, Part No. 285442

standard 76 liters (20 gal.), 86 cm (34")

high drain tub or utility sink and sump

pump (available from local

plumbing suppliers)

nothing

2 longer water inlet hoses: 1,8 m (6 ft.)

hoses, Part No. 76313 or 3 m (10 ft.)

hoses, Part No. 350008

Electrical

Do Not earth to a gas pipe.

Check with a qualified electrician if you are not sure that

washer is properly earthed.

Do Not have a fuse in the neutral or earthing circuit.

In the U.S. only: If codes permit and a separate earthing

wire is used, it is recommended that a qualified electrician

determine that the earthing path is adequate.

If the supply cord of this appliance is damaged, it must be

replaced only by a repair shop appointed by the

manufacturer, because special tools are required.

A 230-volt, 50-Hz, 10-amp, fused electrical supply is required. Time-

delay fuse or circuit breaker is recommended. It is recommended

that a separate circuit serving only this appliance be provided.

Preparation

SLIDE WASHER ONTO CARDBOARD OR HARDBOARD

BEFORE MOVING ACROSS FLOOR.

Move washer close to its final location.

Read, then remove the label (A) that covers the power supply cord

and drain connector. Peel the tape down and off each side of the

cabinet.

Remove shipping strap (B).

Completely remove the shipping strap with 2 cotter pins (C) from

the inside of the washer.

Pull the strap completely out of the washer.

(to washer)

Use new hoses,

washers, and

adapters that

came with your

washer.

Insert one large flat washer (A) into each end of the inlet hoses

(B). Check that washers are firmly seated in couplings (C).

Floor drain system:

Requires a siphon break, Part No. 285320 (B). Siphon break

must be above high-water level in washer, at least 71 cm

(28 inches) from bottom of washer. Additional drain hose

will be needed.

Wall standpipe drain:

Top of standpipe (D) must be at least 99 cm (39 inches)

high and no higher than 183 cm (72 inches) from bottom of

washer.

Laundry tub drain system:

Needs a 76-liter (20-gallon) laundry tub.

Top of tub must be at least 86 cm (34 inches) high and no higher

than 183 cm (72 inches) from bottom of washer (A).

Standpipe drain system:

Needs a 5-cm (2-inch) minimum diameter standpipe with minimum

carry-away capacity of 64 liters (17 gallons) per minute. A 5-cm

(2-inch) diameter to 2.5-cm (1-inch) diameter standpipe adapter, Part

No. 3363920 must be used with 2.5-cm (1-inch) diameter drain system.

Floor standpipe drain:

Top of standpipe (C) must be at least 99 cm (39 inches) high and no

higher than 183 cm (72 inches) from bottom of washer.

Recommended earthing method

For your personal safety, this washer must be earthed. This

washer is equipped with a power supply cord having an earthing

plug.

To minimize possible shock hazard, the power supply cord must

be plugged into a mating earthing-type wall receptacle earthed in

accordance with local codes and ordinances. If a mating wall

receptacle is not available, it is the personal responsibility and

obligation of the customer to have the proper earthed wall

receptacle installed by a qualified electrician.

Pull firmly to remove the other end of the shipping strap (D) from

the back of the washer to release self-leveling legs (E).

Save the shipping strap to secure drain hose.

DO NOT OVERTIGHTEN; this could cause damage to couplings.

Inlets are plastic. DO NOT STRIP OR CROSSTHREAD.

Attach hose (without

adapter) to hot water

(bottom) inlet valve

(D) first; then second

hose (without adapter)

to cold water (top)

inlet valve (E). Tighten

couplings by hand.

Then use pliers to

make additional two-

thirds turn.