Whirlpool 8TLSQ8533LT1 Gebrauchsanweisung - Seite 4

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Waschmaschine Whirlpool 8TLSQ8533LT1 herunter. Whirlpool 8TLSQ8533LT1 12 Seiten. Whirlpool washer user instructions washer

Seite drucken

Style 2: Without liquid chlorine bleach dispenser (on some

models)

Let the washer ﬁll and begin agitating the load.

Add bleach 5 minutes into the wash cycle for best cleaning

and so that bleach can be removed in the rinse cycle. Pour

bleach around the agitator, not directly onto the load to

avoid damaging clothing or other items in the load.

3. (OPTIONAL) Add liquid fabric softener.

NOTE: Do not spill or drip any fabric softener onto the clothes.

Undiluted fabric softener can stain fabrics. Always dilute fabric

softener with warm water. Too much fabric softener can make

some items (diapers and towels) nonabsorbent. If this

happens, do not use it every load, or use less of it in each

load.

Style 1: With liquid fabric softener dispenser (on some models)

Use only liquid fabric softener in this dispenser. Pour

measured liquid fabric softener into the dispenser.

Softener is added automatically during the rinse portion of

the cycle. Dilute liquid fabric softener by ﬁlling the

dispenser with warm water until liquid reaches the

crossbar in the dispenser opening.

Style 2: Without liquid fabric softener dispenser (on some

models)

In the ﬁnal rinse ONLY, add fabric softener that has been

diluted with 250 mL warm water.

4. Close the washer lid. Washer will not agitate or spin with the

lid open.

Cleaning Your Washer

Use a soft, damp cloth or sponge to wipe up any spills such as

detergent or bleach from the outside of your washer.

Clean your washer interior by mixing 250 mL of chlorine bleach

and 500 mL of detergent. Pour this mixture into your washer and

run it through a complete cycle using hot water. Repeat this

process if necessary.

Remove any hard water deposits using only cleaners labeled as

washer safe.

Cleaning the liquid fabric softener dispenser (on some

models):

1. Remove dispenser by grasping top with both hands and

squeezing, while pushing upward with thumbs.

2. Rinse dispenser under warm water, then replace it.

NOTE: Some models are equipped with a liquid fabric softener

dispenser. To avoid damage to the washer or clothing do not wash

clothes with the liquid fabric softener dispenser removed or add

detergent or bleach to this dispenser; it is for liquid fabric softener

only.

Water Inlet Hoses

Replace inlet hoses after 5 years of use to reduce the risk of hose

failure. Periodically inspect and replace inlet hoses if bulges,

kinks, cuts, wear or leaks are found.

When replacing your inlet hoses, mark the date of replacement on

the label with a permanent marker.

5. Turn the LOAD SIZE or WATER LEVEL selector to the correct

setting for your wash load and the type of fabric being

washed. You may change the load size or water level selection

after the washer has started ﬁlling by turning the selector to a

different setting.

6. Set the TEMPERATURE selector to the correct setting for the

type of fabric and soils being washed. Use the warmest wash

water safe for fabric. Follow garment label instructions.

NOTE: In wash water temperatures colder than 21ºC,

detergents do not dissolve well. Soils can be difﬁcult to

remove. Some fabrics can retain wear wrinkles and have

increased pilling (the formation of small lint-like balls on the

surface of garments).

7. (OPTIONAL) EXTRA RINSE selector (on some models). For an

additional rinse and spin at the end of a wash cycle, set the

EXTRA RINSE selector to ON. On some models, the EXTRA

RINSE feature is part of the cycle.

8. (OPTIONAL) Some models have an END OF CYCLE SIGNAL

selector. Set this selector to ON if you want your washer to

alert you when the wash cycle is complete.

9. Push in the Cycle Control knob and turn it clockwise to the

wash cycle you want. Reduce the wash time when using a

small load size setting. Pull out the Cycle Control knob to start

the washer.

To stop or restart your washer:

To stop the washer at any time, push in the Cycle

Control knob.

To restart the washer, close the lid (if open) and pull out the

Cycle Control knob.

WASHER CARE

Because some water may stay in the hoses, freezing can damage

your washer. If storing or moving your washer during freezing

weather, winterize it.

Winterizing your washer

1. Shut off both water faucets. Disconnect and drain water inlet

hoses. Pour 1 L of R.V.-type antifreeze into the basket.

2. Run washer on a drain and spin setting for about 30 seconds

to mix the antifreeze and remaining water.

3. Unplug washer or disconnect power.

To use washer again

1. Flush water pipes and hoses. Reconnect water inlet hoses.

Turn on both water faucets.

2. Plug in washer or reconnect power.

3. Run the washer through a complete cycle with 250 mL of

detergent to clean out antifreeze.

Storage, non-use or vacation care

Operate your washer only when you are at home. If you will be on

vacation or not using your washer for an extended period of time,

you should:

1. Unplug washer or disconnect power.

2. Turn off the water supply to the washer. This helps avoid

accidental ﬂooding (due to a water pressure surge) while you

are away.

Moving & Storage