Whirlpool 3WSC20N4XB00 Gebrauchsanweisung - Seite 6

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Kühlschrank Whirlpool 3WSC20N4XB00 herunter. Whirlpool 3WSC20N4XB00 24 Seiten.

Seite drucken

5. Reconnect water tubing (on dispenser models) and wiring.

IMPORTANT: Do not intertwine the water tubing and wiring

bundles when reconnecting them.

On dispenser models, reconnect the water tubing.

Water Connection Style 1: Push the larger ⁵⁄₁₆" (7.94 mm)

water tube into the blue fitting until it stops, then push the

smaller ¹⁄₄" (6.35 mm) water tube into the green fitting until

it stops. See Graphic 2A.

Water Connection Style 2: Push the black water tube

with the blue tip into the blue fitting until it stops. Close

the clasp around the tubing, making sure it snaps into

place. Repeat this process to connect the red-tipped

black water tube and the red fitting. See Graphic 2B.

NOTE: On dispenser models with the ice storage bin on the

freezer door, there are two wiring bundles that run underneath

the freezer — a large bundle with a large grommet and two

white plugs at the end, and a small bundle with a small

grommet and one yellow plug at the end.

Reconnect the wiring plugs to the electrical housing. See

Graphic 3.

Reinstall the wiring clip over the grommets. On dispenser

models with the ice storage bin on the freezer door, first

install the smaller grommet into the top of the clip, then

install the larger grommet into the bottom of the clip

(closest to the screw hole). See Graphic 3.

Align the clip's screw hole with the hole in the

refrigerator's base crossbar, and screw in the clip. Tighten

screw. See Graphic 3.

IMPORTANT: Once connected, the wiring bundles should

not be taut. Some flexibility is needed to allow the freezer

door to open properly.

6. Replace the refrigerator door by lifting the door onto the

bottom right hinge.

7. Align and replace the top right hinge as shown. See Graphic 6.

Tighten screws.

8. Replace the ice storage bin and any adjustable door or utility

bins.

9. Plug refrigerator into a grounded (earthed) outlet.

Leveling and Door Closing

Your refrigerator has two adjustable front feet — one on the right

and one on the left. In most cases, the refrigerator should be

steady when both feet are touching the floor. If your refrigerator

seems unsteady or if you want the doors to close more easily,

adjust the refrigerator's tilt using the instructions below:

1. Move the refrigerator into its final location. If necessary, open

both doors to 90° and remove the base grille. See Graphic 1.

2. The two leveling feet are located on the brackets on each side

of the product. See Graphic 8.

NOTE: Having someone push against the top of the refrigerator

takes some weight off the leveling feet. This makes it easier to

make adjustments.

3. Use a ¹⁄₄" open-ended or adjustable wrench to adjust the

leveling feet. Turn the leveling foot to the left to raise that side

of the product, or turn it to the right to lower that side of the

product.

4. Open both doors again and check that they close as easily as

you like. If not, tilt the refrigerator slightly more to the rear by

turning the leveling feet to the left. It may take several more

turns, and you should turn both leveling feet the same

amount.

NOTE: Whenever you need to move the refrigerator, turn the

leveling feet to the right until they are no longer touching the

ground. This will allow the refrigerator to roll more easily.

Door Alignment

A refrigerator that is not level from side-to-side may appear to

have doors that are not properly aligned. If the doors appear this

way, use the instructions in the previous section to check the

leveling.

The doors are designed to be slightly different heights when the

refrigerator is empty, in order to account for the weight of food

that will be placed on the doors. If the doors are still not aligned

after checking the leveling and loading the refrigerator with food,

follow the steps below to adjust the door alignment.

1. If necessary, open both doors to 90° and remove the base

grille. See Graphic 1.

2. Locate the alignment screw on the bottom hinge of the

refrigerator door. See Graphic 9.

3. Use a ⁵⁄₁₆" open-ended or adjustable wrench to turn the screw.

To raise the refrigerator door, turn the screw to the right. To

lower the door, turn the screw to the left.

4. Check that the doors are even at the top. If necessary,

continue to turn the alignment screw until the doors are

aligned.

5. Open both doors to 90°. Replace the base grille. See

Graphic 1.

Handle Installation and Removal

PARTS INCLUDED: Door handles (2), ¹⁄₈" hex key, spare

setscrew(s)

To Install the Handles:

NOTE: The handle mounting setscrews are preinstalled in the

handle.

1. Remove the handles, which are packed inside the refrigerator.

NOTE: To avoid scratching the finish, place the handles on a

towel or other soft surface.

2. Open the freezer door. On the refrigerator door, place the

handle on the shoulder screws with the setscrews facing the

freezer.

A. Shoulder screws

B. Setscrews inside the handle

3. Firmly push the handle toward the door until the handle base

is flush against the door.