Whirlpool Cabrio WGD6200SW Handbuch für Gebrauch und Pflege - Seite 18
Blättern Sie online oder laden Sie pdf Handbuch für Gebrauch und Pflege für Trockner Whirlpool Cabrio WGD6200SW herunter. Whirlpool Cabrio WGD6200SW 48 Seiten. Fabric care system gas dryer
Seite drucken
End of Cycle Signal
End of Cycle Signal
The End of Cycle Signal produces an audible sound when the
drying cycle is finished. Promptly removing clothes at the end of
the cycle reduces wrinkling.
Press END OF CYCLE SIGNAL until the desired volume (Loud,
Soft or Off) is selected.
NOTE: When the WRINKLE SHIELD™ setting is selected and the
End of Cycle Signal is on, a tone sounds every 5 minutes until the
clothes are removed, or the WRINKLE SHIELD™ setting ends.
Changing Cycles, Modifiers and Options
You can change Automatic and Timed Cycles, Modifiers and
Options anytime before pressing Start.
Three short tones sound if an unavailable combination is
selected. The last selection will not be accepted.
Changing Cycles after pressing Start
1. Press PAUSE/CANCEL twice.
2. Select the desired cycle and options.
3. Press START. The dryer starts at the beginning of the new
cycle.
NOTE: If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically shuts off.
Changing Modifiers and Options after pressing Start
You can change an Option or Modifier anytime before the
selected Option or Modifier begins.
1. Press PAUSE/CANCEL once.
2. Select the new Option and/or Modifiers.
3. Press START to continue the cycle.
NOTE: If you happen to press PAUSE/CANCEL twice, the
program clears and your dryer shuts down. Restart the selection
process.
Changing the Preset Dryness Level Settings
If all of your loads on all Auto Dry cycles are consistently not as
dry as you would like, you may change the preset Dryness Level
settings to increase the dryness. This change will affect all of your
Auto Dry cycles.
Your Dryness Level settings can be adjusted to adapt to different
installations, environmental conditions or personal preference.
There are 3 drying settings: 1 (factory preset dryness level),
2 (slightly dryer clothes, approximately 15% more drying time)
and 3 (much dryer clothes, approximately 30% more drying
time).
1. The Dryness Level settings cannot be changed while the
dryer is running.
2. Press and hold the DRYNESS button for 5 seconds. The
dryer will beep, and "CF" will be displayed for 1 second
followed by the current drying setting.
18
3. To select a new drying setting, press the DRYNESS button
again until the desired drying setting is shown.
NOTE: While cycling through the settings, the current setting
will not flash, but the other settings will flash.
4. Press START to save the drying setting.
5. The drying setting you selected will become your new preset
drying setting for all Auto Dry cycles.
Drying Rack Option
Use the Drying Rack to dry items such as sweaters and pillows
without tumbling. The drum turns, but the drying rack does not
move.
If your model does not have a drying rack, you may be able to
purchase one for your model. To find out whether your model
allows drying rack usage and for information on ordering, please
refer to the front page of the manual or contact the dealer from
whom you purchased your dryer.
NOTE: The drying rack must be removed for normal tumbling. Do
not use the automatic cycle with the drying rack.
To use the drying rack
1. Open dryer door.
2. Place drying rack inside dryer drum, positioning the back wire
on the ledge of the inner dryer back panel. Push down on
front edge of drying rack to secure at the front of the dryer.
B
A
A. Dryer rack front edge
B. Dryer back panel
3. Put the wet items on top of the drying rack. Leave space
between the items so air can reach all the surfaces.
NOTE: Do not allow items to hang over the edge of the drying
rack.
A
A. Front edge