Whirlpool Cabrio WGD6600VW0 Handbuch für Gebrauch und Pflege - Seite 20
Blättern Sie online oder laden Sie pdf Handbuch für Gebrauch und Pflege für Trockner Whirlpool Cabrio WGD6600VW0 herunter. Whirlpool Cabrio WGD6600VW0 48 Seiten. Steam fabric care system gas dryer
Auch für Whirlpool Cabrio WGD6600VW0: Teileliste (8 seiten)
Seite drucken
Clean the lint screen before each load. A screen blocked by lint
can increase drying time.
IMPORTANT:
•
Do not run the dryer with the lint screen loose, damaged,
blocked or missing. Doing so can cause overheating and
damage to both the dryer and fabrics.
•
If lint falls oft the screen into the dryer during removal, check
the exhaust hood and remove the lint.
Every load cleaning
1. The lint screen is located on the top of the dryer. Pull the lint
screen toward you. Roll lint off the screen with your fingers.
Do not rinse or wash screen to remove lint. Wet lint is hard to
remove.
2. Push the lint screen firmly back into place.
As needed
cleaning
1. Roll lint oft screen with your fingers.
2. Wet both sides of lint screen with hot water.
3. Wet a nylon brush with hot water and liquid detergent. Scrub
lint screen with the brush to remove residue buildup.
4. Rinse screen with hot water.
5. Thoroughly dry lint screen with a clean towel. Insert lint
screen back into dryer.
1. Apply a liquid, nonflammable
household cleaner to the
stained area of the drum and rub with a soft cloth until stain is
removed.
2. Wipe drum thoroughly with a damp cloth.
3. Tumble a load of clean cloths or towels to dry the drum.
NOTE: Garments that contain unstable dyes, such as denim blue
jeans or brightly colored cotton items, may discolor the dryer
interior. These stains are not harmful to your dryer and will not
stain future loads of clothes. Dry unstable dye items inside out to
avoid transfer of dye.
From Inside the Dryer Cabinet
Lint should be removed every 2 years, or more often, depending
on dryer usage. Cleaning should be done by a qualified person.
From the Exhaust Vent
Lint should be removed every 2 years, or more often, depending
on dryer usage.
Replace inlet hoses after 5 years of use to reduce the risk of hose
failure. Periodically inspect and replace inlet hoses if bulges,
kinks, cuts, wear or leaks are found.
When replacing your inlet hoses, record the date of replacement.
Install and store your dryer where it will not freeze. Because some
water may stay in the hoses, freezing can damage your dryer. If
storing or moving your dryer during freezing weather, winterize it.
Non-Use
or Vacation Care
Operate your dryer only when you are at home. If you will be on
vacation or not using your dryer for an extended period of time
you should:
1. Unplug dryer and disconnect
power.
2. Close shutoffvalve
in gas supply line.
3. Clean lint screen. See "Cleaning the Lint Screen."
4. Turn off the water supply to the dryer. This helps to avoid
unintended flooding (dueto a water pressure surge) while you
are away.
To winterize
dryer
1. Unplug dryer or disconnect power.
2. Shut off water faucet.
3. Close shutoffvalve
in gas supply line.
4. Disconnect
water inlet hose from faucet and drain.
To use dryer again
1. Flush water pipes. Reconnect water inlet hose to faucet. Turn
on water faucet.
2. Plug in dryer or reconnect power.
3. Open valve to gas supply line.
Moving care
1. Unplug the power supply cord.
2. Shut off water faucet.
3. Disconnect the water inlet hose from faucet, then drain the
hose. Transport hose separately.
4. Close shutoffvalve
in gas supply line.
5. Disconnect
gas supply line pipe and remove fittings attached
to dryer pipe.
6. Cap the open fuel supply line.
7. Make sure leveling legs are secure in dryer base.
8. Use masking tape to secure dryer door.
20