Whirlpool WGD9400SW1 Handbuch für Gebrauch und Pflege - Seite 19
Blättern Sie online oder laden Sie pdf Handbuch für Gebrauch und Pflege für Trockner Whirlpool WGD9400SW1 herunter. Whirlpool WGD9400SW1 48 Seiten. Electronic gas dryer
Auch für Whirlpool WGD9400SW1: Installationsanleitung Handbuch (32 seiten)
Seite drucken
2.
Place drying rack inside dryer drum, positioning the back wire
on the ledge of the inner dryer back panel. Push down on
front edge of drying rack to secure over the lint screen.
oil
A. Dryer rack front edge
B. Dryer back panel
3. Put the wet items on top of the drying rack. Leave space
between the items so air can reach all the surfaces.
NOTE: Do not allow items to hang over the edge of the drying
rack.
5. Select a timed drying cycle and temperature
(see following
chart). Items containing foam, rubber, or plastic must be dried
on a clothesline or by using the Air Only temperature
setting.
6. You must select a time by pressing the DRY TIME up or down
buttons. Reset time as needed to complete drying. Refer to
the following table.
7. Press and hold START button (about 1 second).
NOTE: Check the lint screen and remove any lint accumulated
from items dried on the drying rack.
This chart shows examples of items that can be rack dried and
the suggested cycle, temperature setting and drying time. Actual
drying time will depend on the amount of moisture items hold.
Rack Dry
Setting
Temp.
Time*
Wool Sweaters
Timed
Low
60
Block to shape and lay flat on
Dry
the drying rack.
Stuffed toys or pillows
Timed
Low
60
Cotton or polyester fiber filled
Dry
Stuffed toys or pillows
Timed
Air Only
90
Foam rubber filled
Dry
(no heat)
Sneakers or canvas shoes
Timed
Air Only
90
Dry
(no heat)
°J/
4. Close the door.
*(Minutes) Reset time to complete drying, if needed.
NOTE: You must remove drying rack for normal tumbling. Do not
use automatic cycles with the drying rack.
DRYER CARE
Keep dryer area clear and free from items that would obstruct the
flow of combustion
and ventilation air.
To clean
1. Pull the lint screen straight up. Roll lint off the screen with
your fingers. Do not rinse or wash screen to remove lint. Wet
lint is hard to remove.
Explosion
Hazard
Keep flammable
materials
and vapors, such as
gasoline,
away from dryer.
Place dryer at least 18 inches (46 cm) above the floor
for a garage installation,
Failure to do so can result in death, explosion,
or fire.
Every load cleaning
The lint screen is located in the door opening of the dryer. The
control panel has an indicator light to remind you to clean the lint
screen before or after each load. A screen blocked by lint can
increase drying time.
2. Push the lint screen firmly back into place.
IMPORTANT:
•
Do not run the dryer with the lint screen loose, damaged,
blocked, or missing. Doing so can cause overheating and
damage to both the dryer and fabrics.
•
If lint falls off the screen into the dryer during removal, check
the exhaust hood and remove the lint. See "Venting
Requirements."
As needed cleaning
Laundry detergent and fabric softener residue can build up on the
lint screen. This buildup can cause longer drying times for your
clothes, or cause the dryer to stop before your load is completely
dry. The screen is probably clogged if lint falls off the screen.
Clean the lint screen with a nylon brush every 6 months, or more
frequently, if it becomes clogged due to a residue buildup.
To wash
1. Roll lint off the screen with your fingers.
2. Wet both sides of lint screen with hot water.
19