Whirlpool WGD9750WL1 Handbuch für Gebrauch und Pflege - Seite 8

Blättern Sie online oder laden Sie pdf Handbuch für Gebrauch und Pflege für Trockner Whirlpool WGD9750WL1 herunter. Whirlpool WGD9750WL1 29 Seiten. Electronic dryer

Seite drucken

The Wrinkle Shield S team feature i snotavailable onDelicate

orSuper Delicate Automatic Cycles a nd Timed C ycles w ith

Low, E xtra Low, and AirOnly Temperature

selected. WRINKLE

SHIELD

without Steam cycle is available for these cycles.

For the Casual Cycle, the WRINKLE SHIELD

STEAM feature

is preset to "ON." The other cycles will retain the WRINKLE

SHIELD

STEAM feature setting.

Cycle Signal

The End of Cycle Signal produces an audible sound when the

drying cycle is finished.

Press until the desired volume (Loud, Soft, or Off) glows green.

NOTE: When the WRINKLE SHIELD

STEAM feature is selected

and the End of Cycle Signal is on, an audible sound will be

emitted every 5 minutes until the clothes are removed, or the

WRINKLE SHIELD

STEAM feature is finished.

Button Sound

You can change the volume of the sound of the beeps. Press until

the desired volume (Loud, Soft, or Off) glows green. The Power

and Cancel buttons will still beep softly even when the Button

Sound volume is set to Off.

Co_trolsLocklUnlock

Hol_ for 3 Seconds

Drum Light

When pressed during a cycle, the Drum Light turns on and will

remain on until pressed again, the door is opened and closed, or

the door is left open for 20 minutes.

Controls Lock/Unlock

To enable the Controls Lock feature when dryer is running:

Press and hold the CONTROLS LOCK/UNLOCK

button for

3 seconds. The control is locked when a single beep is heard and

the Controls Lock status light is on. This feature allows you to lock

your settings to avoid unintended use of the dryer. You can also

use the Controls Lock feature to avoid unintended cycle or option

changes during dryer operation.

•

When the dryer is off, it is not necessary to press the Control

On button before activating the Controls Lock feature.

To unlock:

Press and hold the CONTROLS LOCK/UNLOCK

button for

3 seconds to turn this feature off.

NOTE: When the dryer is running and Controls Lock is on, the

dryer can be stopped by pressing the Pause/Cancel button, but

cannot be restarted until the control is unlocked.

You can change Auto Cycles, Timed Cycles, Options, and

Modifier, and anytime before pressing Start.

•

Three short tones sound if an unavailable combination

selected. The last selection will not be accepted.

Changing

Cycles after pressing Start

1. Press PAUSE/CANCEL twice. This ends the current cycle.

2. Select the desired cycle and options.

3. Press and hold START. The dryer starts at the beginning of the

new cycle.

NOTE: If you do not press Start within 5 minutes of selecting the

cycle, the dryer automatically shuts off.

Changing

Options

and Modifiers

after pressing Start

You can change an Option or Modifier anytime before the selected

Option or Modifier begins.

1. Press PAUSE/CANCEL once.

2. Select the new Option and/or Modifier.

3. Press and hold START to continue the cycle.

NOTE: If you happen to press Pause/Cancel twice, the program

clears and your dryer shuts down. Restart the selection process.

Changing the Preset Dryness Level Settings

If all your loads on all Auto Dry cycles are consistently not as dry

as you would like, you may change the preset Dryness Level

settings to increase the dryness. This change will affect all of your

Auto Dry cycles.

Your Dryness Level settings can be adjusted to adapt to different

installations, environmental conditions or personal preference.

There are 3 drying settings: 1 (factory preset dryness level),

2 (slightly drier clothes, approximately

15% more drying time),

and 3 (much drier clothes, approximately 30% more drying time).

1. The Dryness Level settings cannot be changed while the dryer

is running.

2. Press and hold the Dryness Level button for 5 seconds. The

dryer will beep, and "CF" will be displayed for 1 second

followed by the current drying setting.

3. To select a new drying setting, press the Dryness Level key

again until the desired drying setting is shown.

NOTE: While cycling through the settings, the current setting

will not flash, but the other settings will flash.

4. Press START to save the drying setting.

5. The drying setting you selected will become your new preset

drying setting for all Auto Dry cycles.