Whirlpool YCEP2760KQ1 Installationsanleitung Handbuch - Seite 6

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Trockner Whirlpool YCEP2760KQ1 herunter. Whirlpool YCEP2760KQ1 27 Seiten. Commercial dryer gas or electric

Seite drucken

Now Start...

With dryer in laundry area.

Excessive Weight Hazard

Usetwo or more people to move and

installdryer.

Failureto do so can resultin back or

otherinjury.

3-prong,

ogru_J_ d 'IypO

I _

oxhould

vent

I, 1

i fS

J,_

-" _ I

gas supply Ime

gasshuloffvalve

mTake tape

off front corners of

dryer, Open dryer and remove

the

literature

and parts packages,

Wipe

the interior of the drum thoroughly

with a damp

cloth,

mTake two of the cardboard

corners from the carton

and place

them on the floor in back of the dryer,

Firmly grasp the body of the dryer

and gently lay it on its back on the

cardboard

corners,

mWith one of the legs in hand,

check

the ridges for a diamond

marking, That's how far the leg is

supposed

to go into the hole,

mStaff to screw the leveling

legs

into the holes by hand, (Use a small

amount

of liquid detergent

lubricate

the screw threads

so it is

easier to turn the legs,) Use a 1-inch

wrench

or socket wrench

to finish

turning

the legs until you reach the

diamond

mark,

Now stand the dryer up,

Slide dryer onto cardboard

hardboard

before moving across floor

to avoid damaging

floor covering.

Electrical Shock Hazard

Disconnect power before

servicing.

Replace all parts and panels

before operating.

Failure to do so can result in

death or electrical shock,

m Remove the service door of the

meter case, Lift

the service door

up at the back

and remove,

Install money-

accepting

device,

(Refer to

manufacturer's

instructions

for proper

installation,)

For dryers using coin slides, use

adapter

kit supplied

with dryer,

Replace

the meter case service door,

Put the coin vault with lock and key

the meter

case opening,

m Move dryer close to final

position, Remove

cardboard

hardboard

from under dryer,

m Remove

red cap from gas pipe,

Carefully

move dryer into final

position, Place level on top of the

dryer, first side to side; then front to

back, If the dryer is not level, adjust

the legs of the dryer up or down until

the dryer is level,

m Connect

gas supply to dryer,

Use pipe-joint

compound

resistant to

the action

of L,P, gas for gas

connections,

If flexible

metal tubing

used, be certain

there are no kinks,

If necessary

for service, open the toe

panel, use a putty knife to press on

the toe panel

lock located

at the

center

top of the toe panel, Pull

downward

on the toe panel

to open,

Toe panel

is hinged

at the bottom,

m Open the shutoff valve in the

gas supply line,

• Use a non-corrosive

leak

detection

fluid to check

for leaks,

Bubbles around

connections

will

indicate

a leak, If a leak appears,

shut off gas valve controls

and adjust

connections,

Then check

connections

again,

Close toe panel,

All connections

must be wrench-

tightened.

• To exhaust dryer, see Exhaust

requirements,

Pages 3-4, Connect

exhaust vent system to dryer exhaust

outlet

and exhaust

hood using 4"

(10,2 cm) clamps,

Use caulking

seal exterior wall opening

around

exhaust

hood,

Carefully

move dryer into

final position,

Place level on top of

the dryer, first side to side; then front

to back,

If the dryer is not level, adjust

the legs of the dryer up or down

until

the dryer is level,

• Plug power supply cord

into

grounded

outlet,

Check

dryer operation

(some

accumulated

time may be on the

timer due to factory

testing),

Insert coins in slide and press slide in

slowly, (Operating

time will

accumulate

per number

of coins and

type of timing cam used,) Push

START/RESTARTbutton,

Using a full

heat cycle

(not the air cycle),

let the

dryer run for at least five minutes,

Dryer will stop when time is used up,

Note: Dryer door must be closed for

dryer to operate,

When door is open,

dryer stops, but timer continues

to run,

To restart dryer, close door and push

START/RESTARTbutton,

• If the burner does not ignite

and you can feel no heat inside the

dryer, shut off dryer for five minutes,

Check

that all supply valve controls

are in "ON" position

and that the

electrical

cord is plugged

in, Repeat

five-minute

test,

If drying time is too long,

make sure lint screen is clean,

Page 6