Whirlpool YWED9600TB1 Handbuch für Gebrauch und Pflege - Seite 17
Blättern Sie online oder laden Sie pdf Handbuch für Gebrauch und Pflege für Trockner Whirlpool YWED9600TB1 herunter. Whirlpool YWED9600TB1 48 Seiten. Electronic electric dryer
Seite drucken
Damp Dry Signal
On some models, the Damp Dry Signal may be selected to alert
you that your clothes are approximately
80% dry. This is useful
when you want to remove lightweight items in a mixed load to
avoid overdrying or remove partially dry items that may need
ironing.
The DAMP DRY SIGNAL is usdul when drying bedsheets/linens
in a mixed load. When the signal goes off, open the door to stop
the dryer, rearrange the load inside the dryer, close the door and
restart the dryer to finish the drying cycle. Rearranging the load
will aid in the drying process.
Cii L0 d
Soft
off
D_mpDr
Signal
Press DAMP DRY SIGNAL until the desired volume (Loud, Soft or
Off) glows green.
NOTE: The Damp Dry Signal is available only with the Automatic
Cycles. The Damp Dry Signal is not a selectable option for the
Sanitize cycle.
Cycle Signal
The End of Cycle Signal produces an audible sound when the
drying cycle is finished. Promptly removing clothes at the end of
the cycle reduces wrinkling.
Loud
_ Soft
Off
Cycle
Signal
Press CYCLE SIGNAL until the desired volume (Loud, Soft or Off)
glows green.
NOTE: When the WRINKLE SHIELD
TM
feature is selected and the
End of Cycle Signal is on, an audible sound will be emitted every
5 minutes until the clothes are removed, or the WRINKLE
SHIELD
TM
feature is finished.
Button Sound
You can change the volume of the sound of the beeps. Press
BUTTON SOUND until the desired volume (Loud, Soft or Off)
glows green. The Power and Cancel buttons will still beep softly
even when the Button Sound volume is set to Off.
Loud
S0ft
Off
You can change Auto Cycles, Timed Cycles, Modifiers and
Options anytime before pressing Start.
•
Three short tones sound if an unavailable combination
is
selected. The last selection will not be accepted.
Changing
Cycles after pressing Start
1. Press PAUSE/CANCEL twice. This ends the current cycle.
2. Select the desired cycle and options.
3. Press and hold START. The dryer starts at the beginning of
the new cycle.
NOTE: If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically
shuts off.
Changing
Modifiers
and Options after pressing Start
You can change a Modifier or Option anytime before the selected
Modifier or Option begins.
1. Press PAUSE/CANCEL once.
2. Select the new Modifier and/or Option.
3. Press and hold START to continue the cycle.
NOTE: If you happen to press Pause/Cancel twice, the program
clears and your dryer shuts down. Restart the selection process.
Changing
the Preset Dryness Level Settings
If all your loads on all Auto Dry cycles are consistently not as dry
as you would like, you may change the preset Dryness Level
settings to increase the dryness. This change will affect all of your
Auto Dry cycles.
Your Dryness Level settings can be adjusted to adapt to different
installations, environmental
conditions
or personal preference.
There are 3 drying settings: 1 (factory preset dryness level),
2 (slightly dryer clothes, approximately
15% more drying time)
and 3 (much dryer clothes, approximately
30% more drying
time).
1. The Dryness Level settings cannot be changed while the
dryer is running.
2. Press and hold the Dryness Level button for 5 seconds. The
dryer will beep, and "CF" will be displayed for 1 second
followed by the current drying setting.
3. To select a new drying setting, press the Dryness Level key
again until the desired drying setting is shown.
NOTE: While cycling through the settings, the current setting
will not flash, but the other settings will flash.
4. Press START to save the drying setting.
5. The drying setting you selected will become your new preset
drying setting for all Auto Dry cycles.
Button
Sound
17