Before you start...
Check
location
where
cwktop
will be installed.
The ccoktop
Proper
installation
is the installer's
resDonsibilitv
Make
sure you have
evervihina
-
necessaP/
for correct
instollotion.
It is the
responsibility
of the installer
to comply
with
the installation
clearance
specified
in these
instructions.
should
be located
for
convenient
use I" the kitchen
Important:
Observe all governing
codes and ordinances.
Failure to meet
codes and ordinances
could lead lo
tire or electrtcal
shock hazard.
If cabinet
has a drawer.
D 3" depth
J
clearance
from countertop
fo top of
1%" ml".
^_L.i-^._-_^^
_
drawer
is required.
*NOTE:
New Installations
- Follow
minimum
dimensions
given.
Replacement
installations
- be
sure
that front edge
of cooktop
is at least 1Yz"
back
from front edge
of countertop
and
that
sides ore 1" from vertical
walls
WARNING:
Reaching
over heoted
surface
burners
causes
risk of being
burned
To reduce
risk, Installation
01
cabinet
storage
above
should
be avoided.
If cabinets
ore
already
provided.
reduce
hazard
by
Installing
o cooktop
hood
Hood
should
extend
y minlmum
the lront of cabinets
Grounded
electrical
outlet
IS required.
See Electrical
requirements.
Tools needed
for tnstaIIat3on:
1'1
wrench
Moblle Home Installation
The installation
of this cooktop
must
conform
to the Manufoctureb
Home
Construction
and
Safeiv
Standards.
Title 24 CFR. F'arl32-80
(formerly
the
Federal
Standard
for Mobile
Home
Construction
and
Safety,
Title 24, HUD,
Part 2801. Four-v&
power
supply
cord
must be used and
the appliance
wiring
must be revised
See Electrical
requirements.
Copies
of the standards
listed may
be obtained
from:
"NatIonal
Fire ProtectIon Association
Botferymarch
Park
Qulncy. Massachusetts
02269
PANEL A
Electrical
requirements
Electrical ground is required on
this appliance.
A
A three-wire.single-phase.
H 240 volt. 60 Hz. AC only,
electrical
suoolv
is reauired
on a
separate
5O'&pere
dircuit.
fused on
both
sides of the line. DO NOT fuse the
neutral.
A time-delay
fuse or circuit
breaker
is recommended
B
.
COOKTOP
MUST BE
CONNECTED
WITH COPPER
WIRE ONLY: Aluminum
must not be used
to avoid
potentially
unsatisfactory
connections.
C
Wire sizes must conform
to the
m requirements
of the NatIonal
ElectrIcal
Code.
ANSI/NFPA
713.1987"
and
local
codes
and
ordIn&m-for
the kilowatt
rating
of the cc&top.
The
sMallratIng
plate can be found on the
reorwallofthebumerbox.SeeStep5
for occ85(
to burner
box.
WARNING:
It is the customer's
responsibility
to:
l
contact a qualified, electrical
installer.
l
assure that electrical
installation
is adequate and in
conformance
with National
Electrlcal Code. ANSVNFPA
70-1987** and l&al
D
This appliance
should
be
w
connected
to the fused-
disconnect
[or circuit
breaker1
box
through
flexible.
armored
or
nonmetallic-sheathed.
co-r
cable
[with
grounding
wire].
The &xible.
armored
cable
extending
from the
appliance
should
be connected
directly
to the Junction
box.
E
Locate
the junction
box to
n
allow
OS mu&
slack
In the
cable
as possible
between
the
junction
box and
the appliance.
x3
that
the co&top
can
be moved
if
servicing
is ever necessary.
Do not
cut candutf.
F
A U.L.-listed
strain
relief
must be
n
provided
at the junction
box.
G
It is the personal
responsibility
n
and
obligation
of the
customer
to contact
0 qualified
electrIcian
to assure
that the electrical
installation
is adequate
and
Is In
conformance
with the NatIonal
ElectrIcal
Code,
ANSI/NFPA
704987"
and
local
codes
and
ordinances.
Copies
of the standards
listed may
be
obtalned from:
"Natlonal
Firs ProtectIon Assoclatlon
Batterymarch Pork
Qulncy, Massochusetta 02269
H
n
A wiring
dkzgmm
is located
under
the control
panel
InsIde
the burner
box.
Seite drucken