Whirlpool AKR 799 IX AKR 799 IX Handbuch für Installation und Gebrauch - Seite 12
Blättern Sie online oder laden Sie pdf Handbuch für Installation und Gebrauch für Lüftungshaube Whirlpool AKR 799 IX AKR 799 IX herunter. Whirlpool AKR 799 IX AKR 799 IX 13 Seiten. 90cm spot sensor cooker hood, akr 799 ix
Seite drucken
At the end of cooking and when the ambient parameters
have returned to the levels prior to cooking, the system
switches off.
If the parameters are close to the rest condition, the system
forces hood switch-off after 30 minutes.
AIR QUALITY CONTROL mode, LED "L5" (white) on.
The system promptly reacts to Steam/Gas increases and
remains at the set speed for at least 1 minute, before
returning to the lowest speed/switching off.
When the effect of the Steam/Gas has finished and the
ambient parameters have returned to the levels prior to
start, the system switches off.
Press buttons "1", "2" and "4" to exit this mode".
Sensor test
This occurs continuously during automatic operation. In case
of a failure, all the LEDs blink (contact the After Sales
Service); in any case, the hood can be used in manual mode.
Manual setting
Switch the hood OFF and keep buttons "1" and "4" pressed
at the same time for 3 seconds".
LED "L5" blinking.
It is advisable to carry out this operation when:
• the hood is installed for the first time
• the power supply has been disconnected for many hours
or days
• a sudden temperature changes occurs in the kitchen
Cooking hob selection
This operation optimises automatic hood operation; proceed
as follows:
Switch the hood OFF
Keep buttons "1" and "3" pressed at the same time for 3
seconds until the cooking hob in use is displayed.
LED "L1" on: Gas hob
LED "L2" on: Induction hob
LED "L3" on: Electric hob
Press button "1" for cyclic selection of the hob"
Confirmation of the selected hob is displayed by the
corresponding LED blinking 3 times.
After selecting the hob, wait 10 seconds for function
confirmation".
The default setting is Gas hob.
Maintenance
Grease filters:
Metal grease filters have an unlimited
life and should be washed once a
month either by hand or in a
dishwasher at a low temperature and
with a short cycle. Washing in a
dishwasher can cause grease filters to
turn white, but this in no way affects efficiency.
• Pull out the handle to remove the filter.
Wash the filter and leave it to dry, proceeding in reverse
order to refit it.
5019 318 33278
GB
D
F
NL
E
P
I
GR
Replacing the halogen bulbs:
1. Disconnect the hood from the mains power supply.
WARNING: Wear gloves.
2. Use a small screwdriver to gently prise the lamp cover off
(at the points indicated in Fig. 3).
3. Remove the burnt-out lamp and fit a new one.
WARNING: Replace using 20W max G4 halogen bulbs
only.
Close the lighting unit (snap-on).
Active carbon filter
(filter hoods only):
The carbon filter must be cleaned once a month in a
dishwasher at the highest temperature, using a normal
dishwasher detergent. Wash the filters on their own.
After washing, reactivate the carbon filter by drying it in the
oven at 100°C for 10 minutes.
Change the carbon filter every 3 years.
Fitting the carbon filter:
1. Remove the grease filter.
2. Remove the filter holder by turning the knobs 90°.
3. Fit the carbon filter "i" in the filter holder "h".
Reverse the above procedure to re-fit the filter holder and
grease filter.
N
S
DK
FIN
PL
RUS BG RO
CZ SK
H