Whirlpool W10502583F Installationsanleitung und Gebrauchs- und Pflegeanleitung - Seite 5
Blättern Sie online oder laden Sie pdf Installationsanleitung und Gebrauchs- und Pflegeanleitung für Lüftungshaube Whirlpool W10502583F herunter. Whirlpool W10502583F 48 Seiten. 30" (76.2 cm) wall-mount canopy range hood
Seite druckenTools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed here.
Tools needed
■
Level
Drill with 1¼" (3.0 cm), ³⁄₈" (9.5 mm), and ⁵⁄₁₆" (7.9 mm) drill bits
■
■
Pencil
■
Wire stripper or utility knife
■
Tape measure or ruler
■
Pliers
■
Caulking gun and weatherproof caulking compound
■
Vent clamps
■
Jigsaw or keyhole saw
■
Flat-blade screwdriver
■
Metal snips
■
Phillips screwdriver
Parts needed
■
Home power supply cable
■
½" (12.7 mm) UL listed or CSA approved strain relief
■
3 UL listed wire connectors
For vented installations, you will also need:
■
1 wall or roof cap
■
Metal vent system
For non-vented (recirculating) installations, you will also need:
■
Charcoal Filter Kit Part Number W10412939 for non-vented
(recirculating) installations only. See "Assistance or Service"
section to order.
■
6" (15.2 cm) dia. round metal vent duct - length required
is determined by ceiling height.
Parts supplied
Remove parts from packages. Check that all parts are included.
■
Hood canopy assembly with blower, light bulbs, and canopy
glass already installed
■
Vent transition with back draft dampers installed
■
Metal grease filter
■
Vent cover support bracket
■
Mounting template
■
2-piece vent cover
■
Air deflector (for non-vented [recirculating] installations only)
■
8 - 4.2 x 8 mm screws (T20
■
6 - 5 x 45 mm mounting screws (#2 Phillips drive)
■
2 - 8 x 40 mm wall anchors (masonry)
■
4 - 10 x 60 mm wall anchors
■
4 - 5.4 x 75 mm screws (for 10 x 60 mm wall anchors)
■
2 - 3.5 x 9.5 mm screws (T10 drive)
■
®†
T10 Torx
adapter
■
T20
®
Torx
®
adapter
†®TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.
INSTALLATION REQUIREMENTS
®†
drive)
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility to comply with installation clearances
specified on the model/serial/rating plate. The model/serial/rating
plate is located behind the left filter on the rear wall of the vent
hood.
Canopy hood location should be away from strong draft
areas, such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance.
Grounded electrical outlet is required. See "Electrical
Requirements" section.
The canopy hood is factory set for venting through the roof or
wall. For non-vented (recirculating) installation, see "For non-
vented (recirculating) installation only" in the "Connect Vent
System" section. Charcoal Filter Kit Part Number W10412939
is available from your dealer or an authorized parts distributor.
All openings in ceiling and wall where canopy hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local
codes.
Product Dimensions
10⁷⁄₈" (27.6 cm)
4⁷⁄₈" (12.3 cm)
13³⁄₁₆" (33.5 cm)
30" (76.2 cm)
*For non-vented (recirculating) installations
**For vented installations
5¹⁵⁄₁₆" (15.0 cm)
*27⁷⁄₈" (70.8 cm) min.
46⁹⁄₁₆" (118.3 cm) max.
21"
(53.3 cm)
14³⁄₄"
**27⁷⁄₈" (70.8 cm) min.
(37.6 cm)
42³⁄₄" (108.6 cm) max.
1¹³⁄₁₆"
(4.6 cm)
19¹¹⁄₁₆" (50.0 cm)
5