Whirlpool WVW53UC6HV Installationsanleitung und Gebrauchs- und Pflegeanleitung - Seite 7

Blättern Sie online oder laden Sie pdf Installationsanleitung und Gebrauchs- und Pflegeanleitung für Lüftungshaube Whirlpool WVW53UC6HV herunter. Whirlpool WVW53UC6HV 28 Seiten. 30" and 36" (76.2 and 91.4 cm) wall‑mount canopy range hood

Seite drucken

It is recommended that the vent system be installed

■

before hood is installed.

Before making cutouts, make sure there is proper

■

clearance within the ceiling or wall for exhaust vent.

Check your ceiling height and the hood height

■

maximum before you select your hood.

1. Disconnect power.

2. Determine which venting method to use: roof, wall,

or non-vented.

3. Select a flat surface for assembling the range hood.

Place covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

4. Using two or more people, lift range hood onto

covered surface.

5. Remove wood base from range hood and dispose

of properly.

Range Hood Mounting Screws Installation

1. Determine and mark the centerline on the wall where

the canopy hood will be installed.

2. Select a mounting height between a minimum of 24" (61 cm)

for an electric cooking surface, a minimum of 27" (68.6 cm)

for a gas cooking surface, and a suggested maximum of 36"

(91.4 cm) above the range to the bottom of the hood. Mark a

reference line on the wall.

3. Tape template in place, aligning the template centerline

and bottom of template with hood bottom line and with

the centerline marked on the wall.

A. Centerline

B. Fastener locations

C. Mounting height reference (hood bottom line)

4. Mark centers of the fastener locations through the template

to the wall.

IMPORTANT: All canopy mounting screws must be installed

into wood where possible. If there is no wood to screw into,

additional wall framing supports may be required or use

the (4) 10 x 60 mm wall anchors and 5.4 x 75 mm screws.

Remove the template.

INSTALLATION INSTRUCTIONS

Prepare Location

5. For wood, drill 3/16" (4.8 mm) pilot holes at all locations

where screws are being installed into wood.

For wall anchors, drill 7/16" (10 mm) holes at all locations

where wall anchors are being used.

6. For wood, install (2) 5 x 45 mm mounting screws. Leave

a 1/4" (6.4 mm) gap between the wall and the back of the

screw head to slide range hood into place.

For wall anchors, install the 10 x 60 mm wall anchors

and install the 5.4 x 75 mm screws into the wall anchors.

Tighten until the wall anchors are secure. Back the screws

out 1/4" (6.4 mm).

¹⁄₄"

(6.4 mm)

Vent Cover Support Bracket Installation

Installations using telescoping upper and lower vent

cover assembly

1. Position vent cover bracket on wall about 1/8" (3 mm)

away from the ceiling.

2. Mark the hole locations.

3. Drill (2) 3/8" (9.5 mm) holes for 8 x 40 mm wall anchors

and insert anchors flush with the wall.

A. 8 x 40 mm wall anchors

B. Centerline on wall

C. Vent cover support bracket

D. 5 x 45 mm screws

4. Attach vent cover support bracket to wall.

Complete Preparation

1. Determine and make all necessary cuts in the wall for the

vent system. Install the vent system before installing the

hood. See "Venting Requirements" section.

2. Determine the required height for the home power supply

cable and drill a 1

" (3.2 cm) hole at this location.

3. Run the home power supply cable according to the National

Electrical Code or CSA Standards and local codes and

ordinances. There must be enough 1/2" (12.7 mm) conduit

and wires from the fused disconnect (or circuit breaker) box

to make the connection in the hood's electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

4. Use caulk to seal all openings.