ALCON AT-3000 Benutzerhandbuch - Seite 10
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Schnurloses Telefon ALCON AT-3000 herunter. ALCON AT-3000 13 Seiten. Long-range cordless telephone
Seite drucken16
2
FUN
FUN 2
RING TONE ADJUST :
2
Press FUN 2
FUN
and 0 to set the ring to "OFF".
and 1 to set the ring to "LOW".
and 2 to set the ring to "HIGH".
WARNING: On the side of the Handset there is an ON/OFF switch to turn off
the sound completely of the unit. If you turn the switch to "OFF"
you will be able to receive incoming calls, but you will not know
since there will be no sound.
3
FUN 3
FUN
DIAL SYSTEM SELECT :
3
Press
FUN 3 #
FUN
to choose "TONE" mode. This will be shown on the
#
LCD.
3
*
FUN
Press
FUN 3 *
to choose "PULSE" mode. This will be shown on the
LCD.
4
FUN 4
FUN
SCRAMBLER:
There are two scramble functions incorporated into this system SCRB 1 &
SCRB 2. It is necessary that Handset 1 completes this procedure first and then
all the other Handsets follow the same procedure for the Base Unit to accept the
scramble function of any Handset in the system. Also all the Handsets in the
system must be programmed to either SCRB 1 or SCRB 2 for the Base Unit to
accept the scrambled signal. You cannot have some using SCRB 1 and others
using SCRB 2
4
Press
FUN 4
and
FUN
and
and 2
5
FUN
FUN 5
SERIAL NO. & HANDSET NO. DISPLAY :
5
1 2 3
4
FUN 5
FUN
This function displays the Serial Number and the Handset Number of the
Handset you are using. The first
0
MEM
to cancel the scrambler.
1
MEM
to set scrambler 1.
2
to set scrambler 2.
MEM
5
1
5
1 2 3
4
5
digits
is your Serial Number. The last digit
1
depending on how many handsets you have in your system).
PROGRAM NEW HANDSET INTO YOUR SYSTEM FUNCTION:
6
FUN 6
FUN
CODE
6
FUN
In the STBY mode press
You will see -CODE-- shown on the LCD
Display. Enter the Base Unit Serial Number (5 digits) followed by the Handset
Number you wish to have this Handset be represented by xxxxx x (as shown in
FUN 5). After entering this information, please press MEM to complete this
procedure.
REMEMBER: It is necessary to match the GROUP & TYPE of the new
Handset with the original GROUP & TYPE of Base Unit; otherwise, the
Handset will not be able to link with the Base Unit.
7
FUN 7:
FUN
CODE:23
Adding an Extra Security Code To Your System:
The encode function is another security measure added to your system to further
prevent unwanted use of your system using CTCSS tones for example if one of
your Handsets is stolen and you wish to cancel it from the system. To change the
CTCSS code it is necessary that Handset 1 is the only Handset that can change
this function and the other Handsets will follow it (ie. Handset 1 wishes to
change the CTCSS tone to No. 23. All other Handsets in the system must
change to No. 23 as well, otherwise they will not be able to link). If your
Handset is not Handset 1 (Handset 2-9) and by mistake you change this
function, you will not be able to link with the Base Unit. Unless it is absolutely
necessary, please do not change the factory set CTCSS tone.
7
FUN
Please enter FUN 7
then 01-040 (Handset ID No.) MEM to set your CTCSS
tone.
17
is the Handset Number (from 1-9
MEM