CALEFFI DIRTMAGCLEAN 5790 Programmierhandbuch - Seite 8
Blättern Sie online oder laden Sie pdf Programmierhandbuch für Water Filtration Systems CALEFFI DIRTMAGCLEAN 5790 herunter. CALEFFI DIRTMAGCLEAN 5790 14 Seiten. Self-cleaning magnetic dirt separator strainer
Seite druckensensor 2 clip break
E 16
alarm
sensor 1 pressure
E 20
measurement error
sensor 1 pressure
E 21
measurement over
range error
sensor 1 pressure
E 22
measurement under
range error
sensor 2 pressure
E 26
measurement error
sensor 2 pressure
E 27
measurement over
range error
sensor 2 pressure
E 28
measurement under
range error
sensor 1 temperature
E 23
measurement error
sensor 1 temperature
E 24
measurement over
range error
sensor 1 temperature
E 25
measurement under
range error
sensor 2 temperature
E 29
measurement error
sensor 2 temperature
E 30
measurement over
range error
sensor 2 temperature
E 31
measurement under
range error
sensor 2 erroneously removed during
operation of the device
sudden drop of plant pressure due to
a hose burst event or another fault
sensor internal fault
surpassing sensor maximum pres-
sure
sensor internal fault
sensor internal fault
surpassing sensor maximum
pressure
sensor internal fault
sensor internal fault
surpassing of maximum temperature
of sensor 1 (e.g. device internal
temperature above 100°C)
sensor internal fault
sensor internal fault
surpassing of maximum tempera-
ture of sensor 1 (e.g. device internal
temperature above 100°C)
sensor internal fault
8
refit the sensor correctly and check correct sealing of the sys-
tem. Restart the system by means of an alarm reset.
inspect the plant and check that there are no faults or
anomalous behaviours such as to result in a drop of plant
pressure. Restore the correct static pressure value and restart
the system by performing the alarm reset procedure.
contact the service network and replace the sensor: to do
this, the plant must be de-energised and the device must be
emptied. Once the new sensor has been installed, proceed
with the alarm reset.
check correct operation of the plant, of the expansion vessels
and of the safety relief valves. Surpassing the sensor maximum
pressure values is a very hazardous condition for the plant and
for persons: carry out a general check of the plant.
contact the service network and replace the sensor: to do
this, the plant must be de-energised and the device must be
emptied. Once the new sensor has been installed, proceed
with the alarm reset.
contact the service network and replace the sensor: to do
this, the plant must be de-energised and the device must be
emptied. Once the new sensor has been installed, proceed
with the alarm reset.
check correct operation of the plant, of the expansion vessels
and of the safety relief valves. Surpassing the sensor maximum
pressure values is a very hazardous condition for the plant and
for persons: carry out a general check of the plant
contact the service network and replace the sensor: to do
this, the plant must be de-energised and the device must be
emptied. Once the new sensor has been installed, proceed
with the alarm reset.
contact the service network and replace the sensor: to do
this, the plant must be de-energised and the device must be
emptied. Once the new sensor has been installed, proceed
with the alarm reset.
reduce system temperature and perform the plant safety shut-
down procedure, checking the adjustment systems and plant
safety systems. Excessively high temperatures can damage the
device and other components of the plant. Restart the plant
after having performed the foregoing checks and corrective
actions to guarantee that the maximum temperatures are
within the admissible values.
contact the service network and replace the sensor: to do
this, the plant must be de-energised and the device must be
emptied. Once the new sensor has been installed, proceed
with the alarm reset
contact the service network and replace the sensor: to do this,
the plant must be de-energised and the device and the plant
must be emptied. Once the new sensor has been installed,
proceed with the alarm reset.
reduce system temperature and perform the plant safety shut-
down procedure, checking the adjustment systems and plant
safety systems. Excessively high temperatures can damage the
device and other components of the plant. Restart the plant
after having performed the foregoing checks and corrective
actions to guarantee that the maximum temperatures are
within the admissible values.
contact the service network and replace the sensor: to do this,
the plant must be de-energised and the device and the plant
must be emptied. Once the new sensor has been installed,
proceed with the alarm reset.