Xerox WorkCentre Pro 128 Handbuch zur schnellen Netzwerkeinrichtung - Seite 4

Blättern Sie online oder laden Sie pdf Handbuch zur schnellen Netzwerkeinrichtung für Kopierer Xerox WorkCentre Pro 128 herunter. Xerox WorkCentre Pro 128 7 Seiten. Stand installation guide
Auch für Xerox WorkCentre Pro 128: Installationshandbuch (2 seiten), Handbuch für Auswerter (12 seiten), Broschüre & Specs (6 seiten), Broschüre & Specs (6 seiten), Handbuch installieren (2 seiten), Netzwerk-Handbuch (50 seiten), Handbuch scannen (28 seiten), Schnellinstallationskarte (2 seiten), Hardware-Installationshandbuch (4 seiten), Installationshandbuch für das Zwei-Fach-Modul (4 seiten), Inverter Installation Manual (2 seiten), Installationshandbuch (2 seiten), Hardware-Installationshandbuch (2 seiten), Handbuch zur Standinstallation (2 seiten)

Seite drucken
Xerox WorkCentre Pro 128 Handbuch zur schnellen Netzwerkeinrichtung
Q
u
i
c
k
N
e
t
w
Q
u
i
c
k
N
e
t
w
For WorkCentre M123/M128 WorkCentre Pro 123/128
The System Administrator Guide contains detailed information about Network setups. This
document is intended for setting up the Network using TCP/IP. If using Novell IPX, then see the
System Administrator Guide for setup procedures
Pre-requisites for quick Network Setup using TCP/IP:
1. Confirm that an existing operational network utilizing TCP/IP is available.
2. Confirm that the Ethernet cable is plugged into the M123/M128 and into an operational
Ethernet port on the network.
NOTE:
The Ethernet cable is an RJ45 type and is not supplied by Xerox
Configuring M123/M128 IP address via DHCP:
On startup, the M123/M128 Multifunction device defaults to DHCP to obtain its network
configurations. A DHCP server delivers an IP address as well as other configuration settings to
the device. If you use a DHCP server to allocate an IP address to the M123/M128 device, then
proceed as follows:
Procedure for quick Network Setup using TCP/IP:
Step 1:
Power on the M123/M128 device
Step 2:
Wait a minute or so while the M123/M128 device negotiates an IP address. Then print
out the Network Connectivity Page
To print the Network Configuration Report:
1. Select the Machine Status button on the M123/M128
2. Select Print Report List
3. Select Print Mode Settings
4. Select Setting List – Common Items
5. Press the Start button.
The Network Connectivity Page will be printed. Read the details to confirm that an IP address
has been allocated and that is a valid IP address on your network.
N
OTE:
If the IP address on the Connectivity report starts with 167.xxx.xxx.xxx, then the DHCP
server has not properly allocated an address or DHCP is not enabled on your network.
Step 3
: Record the IP address allocated and from a workstation, open up a web browser (such
as
Internet Explorer).
123/M128 device IP address). If connected properly, you will see the M123/M128 device's
CentreWare Internet Services web page (see below).
QNS
o
r
k
S
e
t
u
p
(
D
o
r
k
S
e
t
u
p
(
D
.
.
Type in the URL
Page 4 of 7
H
C
P
)
H
C
P
)
.
http://xxx.xxx.xxx.xxx
(The xxx's represent the
701P42078