CALI LipLED LLED8700 Installationsanleitung Handbuch

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Arbeitslicht CALI LipLED LLED8700 herunter. CALI LipLED LLED8700 13 Seiten.

Seite drucken

lipLEDs

Installation Instructions

Frosted Lens Cover

(#LLED8700-OL-LF)

6.5"

3.9" or 6.5"

6.5"

End Cap

(#LLED8700-OL-EC)

3.9" or 6.5"

WARNING

• Do not power lipLEDs when coiled or bunched together.

Maintain half inch spacing between parts when lit

• Do not cover lipLEDs as the covering may cause it to overheat, melt, or ignite

3.95"

• Do not puncture or damage lipLEDs

• Do not route lipLEDs through walls, doors, windows, or building structures

• Do not roll out lipLEDs on rough surfaces or over sharp corners.

• Do not use lipLEDs if damaged, such as, broken outer jacket, loose

connections, or frayed wire insulation. Inspect periodically

• Do not secure lipLEDs with staples, nails, or like means that might

damage the insulation. Secure using mounting clips or mounting channel

3.95"

• Do not submerge lipLEDs in liquid or install near standing water or

other liquids

• Do not install lipLEDs where it is subject to continuous flexing

• Do not mount lipLEDs inside cabinets, tanks, or enclosures of any

kind without proper ventilation

• Do not run lipLEDs at an operation temperature exceeding 65C or 149F or

below -20C or -4F

™

6.5" increments up to max run

± 0.125" cutting tolerance

*See max run for more information

6.5" (2.5W) or 3.9" (5.5W) increments up to max run

± 0.125" cutting tolerance

*See max run for more information

Aluminum Extrusion

8' Maximum extrusion and lens length

6.5" increments up to max run

(#LLED8700-OL)

(Dry Location field cuttable)

± 0.125" cutting tolerance

*See max run for more information

2" increments up to max run

± 0.125" cutting tolerance

6.5" (2.5W) or 3.9" (5.5W) increments up to max run

*See max run for more information

± 0.125" cutting tolerance

(Run lengths required)

*See max run for more information

2" increments up to max run

8' Maximum extrusion and lens length

± 0.125" cutting tolerance

(Dry Location field cuttable)

*See max run for more information

Specify Length (19.7"Assembly Increments)

2" increments up to max run

(Add 2.5" to run for end cap and strain relief)

± 0.125" cutting tolerance

*See max run for more information

(Run lengths required)

6" increments up to max run

*See max run for more information

2" increments up to max run

± 0.125" cutting tolerance

*See max run for more information

3.95" increments up to max run

± 0.125" cutting tolerance

*See max run for more information

Specify Length (19.7"Assembly Increments)

(Add 2.5" to run for end cap and strain relief)

6" increments up to max run

*See max run for more information

2" increments up to max run

± 0.125" cutting tolerance

*See max run for more information

3.95" increments up to max run

± 0.125" cutting tolerance

*See max run for more information

8' Maximum extrusion and lens length

2" increments up to max run

8' Maximum extrusion and lens length

± 0.125" cutting tolerance

*See max run for more information

8' Maximum extrusion and lens length

Lens and extrusion shipped in

8' sections (field cuttable)

CALIFORNIA ACCENT LIGHTING, INC.

2034 E. Lincoln Ave. #431, Anaheim, CA 92806

ph. 800.921.CALI (2254) or 714.535-7900 \ fx. 714.535.7902

8' Maximum extrusion and lens length

[email protected] \ calilighting.com

Power Connector

(#LLED8700-PC)

End View

1.20"

• Use only standard outdoor extensions cords, such as, SW, STW, STOW,

SJW, SJOW, SJTW, and SJTOW

• Ground Fault Circuit Interruptor (GFCI) protection is required on

circuits or outlets when lipLEDs is used for outdoor applications

• Surge protector must be set up for electrical power system to avoid

damaging lipLEDs lighting system

INSTALLATION TOOLS REQUIRED

• Electric Compound Miter Saw

• 14.4 to 28 Volt Cordless Drill

• Wire Strippers for 22 and 15

gauge wire

• Pliers

1.20"

• Wire Cutter

• Phillips Bits - Sufficient Quantity

• Carbide Masonry Drill Bits -

Sufficient Quantity

1.46"

LLED8700-OL

Overview

1.46"

IMPORTANT

VERIFY CORRECT

LUMINAIRE WAS RECEIVED WITH

CORRECT COLOR TEMPERATURE

AND VOLTAGE BEFORE CUTTING

OR INSTALLING. CALI WILL NOT

BE RESPONSIBLE IF INCORRECT

LUMINAIRE IS INSTALLED.

• Concrete Tapcon Screws

• Self Drill Metal Screws #4 x 1/2"

- Sufficient Quantity

• Electrical Cords

• Electrical Three Way

• Safety Glasses

• Measuring Tape

• Marker

• Chalk Line

1 of 12

.78"

.75"

5.5W

.78"

.75"

5.5W