Yamaha ca-410 Benutzerhandbuch - Seite 9
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Verstärken Yamaha ca-410 herunter. Yamaha ca-410 13 Seiten.
Seite druckenand
defective
stereo
connect
the
left-hand
speaker
term
inals
and
R
IGHT
term
inals.
image-
Also be
sure
1o
speaker
to
the
LE
FT
the
right-hand
to
the
the
VOLU|\ilË
well
below
this
setting when
lower-
ing
the
cartridge:
at
normal
or
high
volùmes
the
shock may
damage
your
speakers
despite
the
protectrve relay.
Use
the BASS
and
TREBLE controls
to
give
the
most
pleasant
tonal
balance.
At
low
listening
volumes,
the
LOUDNESS
switch
will
qive
a
more
natural
tonal
balance
in
the
ON
position. On
the
other
hand,
at
higher
volumes,
the ON
position
gives unnaturally
exaqgerated
bass
and
treble
response.
The
CA-410
is
designed
for
speakers
with
impedances
between
4
and
l6
ohms.
Use only
speakers
which
are
rated
to
tâke
the
full
25 Watts
o{
CA
410
output
power,
or
set
the VOLU[/]E
so
that the
rated maximum
speaker
input
power
is
not
exceeded, as
indicated
on the
meter
readings.
Speakers
can
be
seriously
damaged
by
even
brief
overloads. Remember
that with 4 ohm
speakers
the
reading
must
be
doubled
(i.e.
if
the
meters
read
20
Watts,
the
real power
is
40 Wattsi,
and
halved
for
16
ohm
speakers.
Making
the
Speaker
Connections
1.
Strip
the
insulated covering Trom
the
speaker
connecting
cable
for
approximately
half
an
inch, and twist any stray
ends
together. lf
possible,
apply
solder
to
the
exposed
half
inch:
stray
ends
can
cause
short-circuiting
of
the
output
terminals,
with
possible damage
to
the
CA-410 {although
it
is
well protecïed by
safety
relay).
Push
the
lever beneath
the
terminal
as
shown
in
the
diaqram,
and align
the
inner
and
outer
terminal
holes.
Then
insert
the wire
fully
home.
Release
the
lever,
and the
wire
end
will
be
fully
and
firmly
gripped, making
a
perfect
connectron.
2.
Be
careful that the terminals
identified
by
the
+
and
-signs
above
them
are
connected
with
the
+
and
-
terminals
on
the
speakers.
A
mistake
in
this polarity
can result
in
poor
bass response
The output
cable
from the
turntable
unit
should be
connected
to
the
PHONO
terminals.
Plug
the pin
jacks attached
to
the
cables
firmly
into the
terminal
sockets,
making
sure
that
the
left-hand
cartridqe
output is
connected
to
the
LEFT
(upper)
socket,
and
the
right-hand
to
the
RIGÈT (lower) socket.
Turntables
are
usually
provided
with
a
third,
GROUND, line.
Be sure
to
connect
this
to
the GND
terminal,
screwing
down
the retaining nut
firmly.
To
enjoy record audition, turn the
INPUT
SELECTOR switch
to
PHONO,
turn
the
VOLUI\4E
welt down,
and
gently lower
the cartridqe
stylus to
the
record surface.
Raise
the
volume
to
the
normal
listeninq
level,
and note
the
selling.
Always lowel