Directed Xpresskit DBALL2 Installationshandbuch - Seite 8

Blättern Sie online oder laden Sie pdf Installationshandbuch für Zubehör für Kraftfahrzeuge Directed Xpresskit DBALL2 herunter. Directed Xpresskit DBALL2 18 Seiten. Ford5 remote start ready (rsr) installation
Auch für Directed Xpresskit DBALL2: Installationshandbuch (12 seiten), Installationshandbuch (19 seiten), Installationshandbuch (18 seiten), Handbuch (14 seiten), Installationshandbuch (13 seiten), Installationshandbuch (14 seiten), Installationshandbuch (19 seiten), Installationshandbuch (16 seiten), Installationshandbuch (20 seiten), Installationshandbuch (15 seiten), Handbuch für Installation und Kurzanleitung (16 seiten), Installationshandbuch (16 seiten), Installationshandbuch (18 seiten), Installationshandbuch (16 seiten), Handbuch (19 seiten), Installationshandbuch (11 seiten), Installationshandbuch (10 seiten)

Seite drucken
Directed Xpresskit DBALL2 Installationshandbuch
Platform: DBALL2
Firmware:
HYUNDAI9 Remote Start Ready (RSR) Installation

Module Programming

Refer to the LED Diagnostics section for more information and for troubleshooting purposes.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the XL202 or SmartStart module to DBALL, it is important to ensure that the proper feature and
function programming is selected using XpressVIP (version 4.5 or higher). Visit www.directechs.com to download the latest
version of the application.
Warning!
To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and
select the Config for RSR button.
3. Follow the instructions to select your vehicle, installation
type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
When the flashing operation is successful, you can proceed with the programming instructions below.
SmartStart Installation
The DBALL module must be disconnected from any power source before SmartStart can
be connected to it. Failing to do so could damage DBALL.
a.
To
ensure that the D2D communication between SmartStart and DBALL works properly, the
Gray wire must be connected to a ground source (Rev B SmartStart), and the Brown or Blue
loop must be cut (Rev A SmartStart).
b.
Do NOT connect the 2-pin harness (on SmartStart). Power and ground will be provided by
the DBALL D2D connector.
Connect SmartStart to DBALL using the D2D port.
OR
XL202 Installation
Connect XL202 to DBALL using the D2D port.
Connect the 10-pin, 12-pin and 14-pin harnesses to
1
DBALL2, then wait until the LED turns ON solid red.
NOTE: To skip the transponder programming and use convenience features only press
the programming button 5 times. The LED will turn orange then proceed to step 2.
Important: Do NOT press the brake pedal. Make sure the
key is inside the vehicle.
2
Press the Push-to-Start (PTS) button twice to turn the
ignition ON.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or
tablet.
3. Select FLASH YOUR MODULE and follow the on screen
instructions.
st
1
Go to the next page to complete the module programming.
SmartStart
XL202
rd
3
nd
2
Do NOT
2X
depress the
Key Inside
brake pedal
the Vehicle
© 2015 Directed. All rights reserved.
Rev.: 20161206
Page 8
&
Solid
ENGINE
PUSH
START
STOP