ALDI 54731 Benutzerhandbuch - Seite 12
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Bohrer ALDI 54731 herunter. ALDI 54731 16 Seiten. 24v lithium-ion cordless drill with hammer action & 2 x batteries
Seite drucken
Drill / driver Overload
Drill/driver Overload
This drill/driver is fitted with an overload protection. If the drill/driver is
excessively forced, or the task being performed is too great for the drill/
driver, the drill/driver will automatically go into an overload mode. When
the drill/driver goes into overload, the drill/driver will automatically and
suddenly STOP. To reset the overload, simply release the trigger. When the
trigger is pressed again, the drill/driver will restart. Resume work after the
overload has been reset, but reduce the load by using a smaller drill/driver
bit or re-sharpen the existing drill/driver bit and reduce the amount of force
placed on the drill/driver. If the drill/driver is set to High speed on the gear
selector, consider changing to low speed selection.
CAUTION. Do not continue to overload the drill/driver and constantly reset
the overload. Doing this will cause the battery cells to over heat.
Temperature cut out
If the drill/driver is constantly overloaded, or the drill/driver is used
constantly at maximum rating in high ambient conditions, the battery cells
may overheat causing the battery pack to shut down.
When this occurs you will need to allow the battery cells to cool.
NOTE: The drill/driver will not restart until the battery pack has cooled.
To reduce the temperature of the cells remove the battery pack from the
drill/driver and place the battery pack in a free air environment, out of direct
sunlight or any other heat source.
DO NOT force cool the pack in any way. Do not place in refrigerators or
freezers.
When the battery pack has cooled down it can again be used to operate
the drill/driver, as long as the load or the conditions causing the original
excessive temperature has been corrected.
Low voltage cut out
The battery pack used on this tool is fitted with a low voltage cut out feature
within the circuitry.
The low voltage cut out feature operates when the voltage drops below a
preset value. This feature automatically stops the drill/driver from operating
(similar to that of the overload condition). When this condition occurs you
will need to either insert another battery into the drill/driver or recharge the
existing battery.
20
e-mail: [email protected]
MODEL: №. 2024001 • 02/2017 • 55945
24v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
1800 909 909
(toll free)
24v Lithium-ion Cordless Drill with Hammer Action
The low voltage cut out feature has been added to maximise the life of the
battery cells in the battery (9). When this occurs, recharge the battery pack
by following the battery charging section in this manual.
NOTE: Attempting to restart the tool without either recharging the battery
or installing another battery (with charge) will lead to drill/driver restarting
and then stopping again, after only a few seconds of operation.
Drill/driving
Drill/driving metals
• Always clamp sheet metal.
• Support thin metal with a block of wood to avoid distorting it.
• Use a punch to mark the centre of the hole.
• Use a suitable lubricant for the material you are working on,
USE:
FOR:
Oil
Steel
Turpentine or paraffin
Aluminium
Do not lubricate
Brass, copper or cast iron
Do not Lubricate
Concrete based material
Drill/driving plastics and plastic coated chipboard
• Use high speed drill/driver bits
• See drill/driving wood below
Drill/driving wood
• Clamp a piece of scrap wood to the back of your work to prevent
splintering.
Hammer drill operations.
• Where possible, use High speed.
• Select the hammer position on the function selection collar (3).
• Use drill bits specifically for masonary applications.
• Ensure to wear safety glasses.
AFTER SALES SUPPORT
1800 909 909
(toll free)
Drill / driving
21
e-mail: [email protected]
MODEL: №.2024001 • 02/2017 • 55945