Directed Directechs DB3 Installationshandbuch - Seite 4

Blättern Sie online oder laden Sie pdf Installationshandbuch für Automobilelektronik Directed Directechs DB3 herunter. Directed Directechs DB3 18 Seiten. Smart key for 2013 toyota highlander
Auch für Directed Directechs DB3: Installationshandbuch (20 seiten), Installationshandbuch (19 seiten), Handbuch (6 seiten), Installationshandbuch (18 seiten), Installationshandbuch (18 seiten), Installationshandbuch (19 seiten), Installationshandbuch (20 seiten), Installationshandbuch (19 seiten), Installationshandbuch (20 seiten), Installationshandbuch (10 seiten), Installationshandbuch (19 seiten), Installationshandbuch (19 seiten), Installationshandbuch (20 seiten), Installationshandbuch (20 seiten), Installationshandbuch (20 seiten), Installationshandbuch (10 seiten), Installationshandbuch (20 seiten), Installationshandbuch (20 seiten), Installationshandbuch (19 seiten), Installationshandbuch (20 seiten), Installationshandbuch (20 seiten), Installationshandbuch (20 seiten), Installationshandbuch (19 seiten), Installationshandbuch (19 seiten), Installationshandbuch (18 seiten), Installationshandbuch (19 seiten), Installationshandbuch (20 seiten), Installationshandbuch (18 seiten), Installationshandbuch (19 seiten), Installationshandbuch (20 seiten), Installationshandbuch (20 seiten), Installationshandbuch (20 seiten), Installationshandbuch (18 seiten), Installationshandbuch (20 seiten), Installationshandbuch (19 seiten), Installationshandbuch (20 seiten), Installationshandbuch (18 seiten), Installationshandbuch (19 seiten), Installationshandbuch (20 seiten), Installationshandbuch (17 seiten), Installationshandbuch (20 seiten), Installationshandbuch (18 seiten)

Seite drucken
Directed Directechs DB3 Installationshandbuch

Pre-installation and application warnings

Firmware notes: This section highlights important information for this specific firmware and will assist in
pricing accordingly, as well as bringing awareness to any operational or vehicle limitations.
T-Harness
compatible
Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic
Š
connector.
Refer to the "Vehicle connections" following the installation diagram.
Š
Connect the hood switch if factory equipped. If NOT, a hood switch must be installed and connected to the remote starter.
Š
Autolights Interrupt ONLY required if vehicles are equipped with Autolights.
Š
OR
AUX1 and AUX2 are only available to control sliding doors on the Sienna using firmware 3.00 +.
General notes: This section highlights important information for this specific firmware.
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D
[1]
The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin or
[2]
NOT supported in data.
Autolights Interrupt ONLY required if vehicles are equipped with Autolights.
[3]

Key type

Some Toyota 2010+ models have different encryption types. Please look at your key blade and identify the markings.
H-stam ped keys
For vehicles with H-stamped keys, see
the TL10 firmware.
H
4
403.TL5 4.00 2012 Toyota Avalon (G Key)
©2021 VOXX•DEI LLC. All rights reserved.
G-stam ped keys
For vehicles with G-stamped keys, see
the TL5 & TL7 firmware.
Keys required for
Keys required for
1
programming
operation
Standard Key
For vehicles with dot-stamped keys,
see the TL11 firmware.
Note:
Some replacement keys
may not have any markings on
the key.
0