Alecto Hesdo DBX-90 Gebrauchsanweisung - Seite 5

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Babyphone Alecto Hesdo DBX-90 herunter. Alecto Hesdo DBX-90 7 Seiten.

Seite drucken

4. Place the transmitter about 1 m from the crib with the microphone 5 facing towards

the baby.

5. Adjust the microphone sensitivity using the up/down button 2 such that the unit

will be set to transmit whenever the microphone 5 picks up a sound at your

desirable loudness level. The microphone sensitivity bar graph in the LCD will also

change correspondingly. More segment of bar graph shown means the unit is more

sensitive to sound.

6. Once the unit is in transmit mode, the LCD will be backlighted and the transmit

icon

will be shown. The transmitter will return to standby mode a few seconds

after the microphone 5 stops picking up any sound and the transmit icon

off. The LCD backlight will also go off to save battery power.

7. When the Out-of-range alert function is set to On, the transmitter will transmit a

signal to the receiver at regular intervals even when the microphone 5 does not

pick up any sound. The transmit icon

8. The night light 4 can be set permanently ON by moving the power ON/OFF switch

1 to

position, the night light icon

light can also be set to be VOX (voice activated) by momentarily pressing the mode

button 3 , the VOX icon will be shown besides the

the night light will be switched on once the microphone 5 detects a sound and

automatically goes off a few seconds after the microphone 5 stops picking up

any sound. Momentarily press of the mode button 3 will cause the night light to

toggle between permanent ON and VOX.

9. The condition of the battery is shown by the battery status indicator

the battery power is being consumed, the segments within the battery status

indicator gradually falls. Once the indicator becomes empty, it will start flashing,

besides, the transmitter will also send out a signal to the receiver to alert the parents.

10.Each time a button is pressed, a beep tone will be heard to validate your entry

being recognized by the unit.

RECEIVER

1. Setting of channel, digital code, upper/lower temperature limit and Out-of-range

alert function.

a. Set the power ON/OFF switch 8 to ON position to turn on the unit. The LCD

screen will show up and become backlighted. Press and hold mode button 10 for

at least 5 seconds to enter into programming mode. A confirmation beep tone will

be heard once the unit goes into programming mode successfully and the LCD will

show following:

Flashing

Light up steadily

goes

will blink correspondingly in the LCD.

will be shown in the LCD. The night

icon. Under VOX mode,

. When

b. Use Up/Down button 9 to select a channel same as the transmitter. Each press

of the button will cause the channel no. to advance or retreat one step. Press and

hold the Up or Down button 9 will cause the channel no. to scroll up or down

rapidly. Confirm your selection by pressing the mode button 10 . The LCD will show

following:

c. Now select the same digital code as the transmitter using the Up/Down button

9 . Each press of the button will cause the digital code to advance or retreat one

step. Press and hold the Up or Down button 9 will cause the digital code to scroll

up or down rapidly. Confirm your selection by pressing the mode button 10 . The

LCD will show following :

d. Now select the same setting for Out-of-range alert function as per the transmitter

using Up/Down button 9 . If a different setting is selected, either false alarm will

be heard or no alarm will be provided even when receiver falls beyond the

communication range of transmitter. Confirm your selection by pressing the mode

button 10 . The LCD will show following:

N.B. In case the transmitter is set to operate with range check function, the reciever

will automatically enters range check mode (as indicated by the letter " C " on LCD) no

matter the out-of-range setting is ON or OFF .

Out-of-range alert setting in Transmitter

Out-of-range alert setting in Receiver

OFF

ELo

ON or OFF

e. Using the Up/Down button 9 , set the upper temperature limit above which the

unit will provide a temperature alarm. Each press of the button will cause the

temperature to advance or retreat one step. Press and hold the Up or Down button

9 will cause the temperature to scroll up or down rapidly. The allowed selectable

temperature range is - 3˚C to + 49˚C . In case O

limit is set. Confirm your selection by pressing the mode button 10 . The LCD will

show the following:

Remarks

Alarm function normally

No alarm even when out of range

Always give alarm no matter out of

range or not

No alarm even when out of range

Alarm sound once distance apart

exceed 20-30m (provide " C " appears

on rerceiver LCD)

is selected, no upper temperature