Directed Xpresskit DBALL2 Installationshandbuch - Seite 10

Blättern Sie online oder laden Sie pdf Installationshandbuch für Durch Schlösser Directed Xpresskit DBALL2 herunter. Directed Xpresskit DBALL2 20 Seiten. Ford5 remote start ready (rsr) installation
Auch für Directed Xpresskit DBALL2: Installationshandbuch (12 seiten), Installationshandbuch (19 seiten), Installationshandbuch (18 seiten), Handbuch (14 seiten), Installationshandbuch (13 seiten), Installationshandbuch (14 seiten), Installationshandbuch (19 seiten), Installationshandbuch (16 seiten), Installationshandbuch (15 seiten), Handbuch für Installation und Kurzanleitung (16 seiten), Installationshandbuch (18 seiten), Installationshandbuch (16 seiten), Installationshandbuch (18 seiten), Installationshandbuch (16 seiten), Handbuch (19 seiten)

Seite drucken
Directed Xpresskit DBALL2 Installationshandbuch
Platform: DBALL2
Firmware FORD3 emote Start
:
R

Module Programming

Refer to the
LED
Diagnostics section on page 14
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to
ensure everything is correct prior to moving onto the next step.
Note: Before connecting either the
function programming is selected using Xpress
version of the application.
Warning!
To take advantage of advanced features, you must use Xpress
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and
select the
Config for RSR
3. Follow the instructions to select your vehicle, installation
type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
When the flashing operation is successful, you can proceed with the programming instructions below.
SmartStart Installation
The
DBALL
module
must
be connected to it. Failing to do so could damage
a.
To
ensure that the D2D communication between SmartStart and
Gray wire must be connected to a ground source (
loop must be cut (
Rev A
b.
Do
NOT
connect the 2-pin harness (on SmartStart). Power and ground will be provided by
the
DBALL
D2D connector.
Connect SmartStart to
DBALL
OR
XL202 Installation
Connect
XL
202 to
DBALL
using the D2D port.
Connect the 10-pin
1
DBALL, then w
ait until the
Remove battery from the factory keyless remote. If the
2
vehicle has two remotes, make sure that the second
remote is at least 10 feet away from the vehicle.
Insert
factory keyless remote
3
to the key port
(located in the center console)
Important: Do
NOT de
4
Press the Push-to-Start (
LED flashes green (fast).
Ready (R
SR Installation
s
-15
XL
202 or SmartStart module to
VIP
(version 4. or higher). Visit www.directechs.com to download the latest
button.
be disconnected from any power source before SmartStart can
DBALL
Rev B
SmartStart).
using the D2D port.
, 1
2-pin
and 14-pin
harnesses to
LED
turns
ON
solid red
(without battery) in
.
press the brake pedal.
PTS
) button
twice to
Go to the next page t complete the module programming.
)
for more information and for troubleshooting purposes.
DBALL
, it is important to ensure that the proper feature and
5
VIP
4.5 (and higher) or the Directechs Mobile app.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your
2. Launch the Directechs Mobile app on your smartphone or
tablet.
3. Select
FLASH YOUR MODULE
instructions.
.
DBALL
works properly, the
SmartStart), and the Brown or Blue
.
st
1
Remove battery
+
from 1st FOB Key
Insert 1st FOB Key
turn
the ignition
ON
.
o
Rev.: 20170908
XKL
oader3.
and follow the on screen
SmartStart
XL202
&
rd
3
nd
2
&
2nd
FOB
Key
more than 10 feet away
Key
port
(center console)
Do NOT
ENGINE
&
&
de
press the
START
STOP
brake pedal
Press x2
© 2017 Directed. All rights reserved.
Page 10
Solid
flashes
(fast)