Alecto ADB-19 Einrichtung

Blättern Sie online oder laden Sie pdf Einrichtung für Zubehör Alecto ADB-19 herunter. Alecto ADB-19 2 Seiten.
Auch für Alecto ADB-19: Einrichtung (2 seiten), Installationshandbuch (2 seiten), Schnellstart-Handbuch (2 seiten)

Seite drucken

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

ADB-19 Installation

double-sided adhesive tape.

Indoor-unit:

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Outdoor-unit:

Auto-leaning Code Wireless Door Chime

Accessories List:

● 1 x Receiver

Accessories List:

● 1 x User Manual

● 1 x Receiver

● 1 x 3 volts CR2032 battery for transmitter

● 1 x User Manual

● 1 x 3 volts CR2032 battery for transmitter

Technical Specification:

● Frequency: 433.92MHz+100KHz

● Modulation Type: ASK

Technical Specification:

● Ring Volume:＞85dB(within 0.5m)

● Frequency: 433.92MHz+100KHz

● Channel space: 1 million sets of auto-learning codes

● Modulation Type: ASK

● Receiver bandwidth: ±90KHz

● Ring Volume:＞85dB(within 0.5m)

● Reception Sensitivity:＞-105dBm

● Channel space: 1 million sets of auto-learning codes

● Transmitter Power:＜10mW

● Receiver bandwidth: ±90KHz

● Power consumption(Receiver): standby:＜0.3W

● Reception Sensitivity:＞-105dBm

● Power consumption(Transmitter): standby:＜5uA working:＜10mA

● Transmitter Power:＜10mW

● Power Supply(Receiver): AC110-240V

● Power consumption(Receiver): standby:＜0.3W

● Power Supply(Transmitter): DC 3V (1x CR2032)

● Power consumption(Transmitter): standby:＜5uA working:＜10mA

● Operating Range:＞150m (in the open air)

● Power Supply(Receiver): AC110-240V

● Power Supply(Transmitter): DC 3V (1x CR2032)

Names for Parts:

● Operating Range:＞150m (in the open air)

Connecting:

Names for Parts:

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat s

and place the battery. Please be well noted with the correct battery polarity. To repla

battery, operate in the same way.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bott

and place the battery. Please be well noted with the correct battery p

battery, operate in the same way.

Instruction Manual

Auto-leaning Code Wireless Door Chime

Instruction Manual

Model No.: QH-861AK

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please re

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and ca

risk of fire and personal injury. Batteries should not be left in an area where the ch

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

Important Note:

● Stick the Transmitter on the wall or the door with

● If you do not plan to use the device for a long time, such as at a vac

double-sided adhesive tape.

battery from Transmitter, then put them in a safe place.

Receiver Installation:

● Improperly using a battery may cause it to leak and damage nearb

● Plug the Receiver into any socket of AC110~240V power.

risk of fire and personal injury. Batteries should not be left in an are

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practic

CODE

MODE

CODE

VOL

Transmitter Installation:

MODE

● Stick the Transmitter on the wall or the door with

VOL

double-sided adhesive tape.

● 1 x Transmitter

● 1 x Double-sided adhesive

● 1 x Transmitter

● 1 x Double-sided adhesive

<10 sec.

Press lightly the ba

holder at side

CR2032 3V Lithium Ba

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

Pres

hold

CR203