Nikon ZOOM800 Gebrauchsanweisung - Seite 10

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Filmkamera Nikon ZOOM800 herunter. Nikon ZOOM800 21 Seiten.

Seite drucken

MAIN FEATURES

Powerful 38-130mm multi coated zoom lens with as-

l 7-zone passive multi AF in 1024 measuring steps

scape, etc.

Compact and light weight body

BEFORE USING

A fast film such as IS0 200 or IS0 400 is recom-

mended to prevent blurriness and to obtain a longer

flash range.

blinks to warn you that an out-of-focus picture will

occur. Set Landscape mode or use Focus Lock func-

tion. (page 24, 29)

trips abroad, etc. ) test the camera and learn how it

works.

CAUTIONS

it is dangerous, do not attempt to take the cam-

era apart.

For ZOOM800 QD only; The date display [ " 00 0 O]

blinks when the batteries are replaced. Ey pressing

either the Mode Button, Select Button, or Set But-

ton, [l 1 ' 951 will be displayed. Reset the correct time

and date.

When replacing the batteries, do so as quickly as

possible to avoid erasing camera memory. We rec-

ommend replacing the batteries when there is no

film in the camera.

The batteries can explode or cause burns if dis-

posed of in fire or if shorted, disassembled,

heated or recharged.

Recommended Replacement 3V Lithium Batteries:

TURNING THE POWER ON/OFF

The power is turned on or off by selecting ON or OFF

on the Drive Dial. (Fig. 6)

When the power is turned on, the lens moves from the

storage position to the wideangle position, and the cam-

era is set automatically lo the mode selected on the

Mode Dial.

CHECKING THE BAlTERlES

appear on the LCD Panel. Replace wilh new batter-

ies as soon as possible.

the internal parts of the camera, as it contains a

high voltage circuit. Take the camera lo an au-

thorized Nikon dealer or service center.

ATTACHING THE STRAP

1. Insert the small loop at the end of the strap under

the Strap Holder. (Fig. 1 0)

2. Insert the other end of the strap through the loop to

tie the strap onto the Strap Holder. (Fig. 1 0)

INSERTING THE BATTERIES

The camera will not operate unless the batteries are in-

stalled. Make sure that the batteries are installed cor-

rectlv.

Cover to open it. (Fig. 2)

Slide the inner cover latch in the direction indicated

to open. (Fig. 3)

Insert the recommended' 3 volt lithium batteries,

checking that the + and - are inserted correctly.

(Fig. 4)

Press down the inner cover to close.

Close the Battery Compartment Cover by pushing it

in the direction indicated unttl it locks firmly in place.

(Fig. 5)

Do not remove the batteries from the camera until

you are ready to replace them.

2. When Ihe batteries are exhausted, the o symbol

will blink in the LCD Panel. Replace with new batter-

ies.

temperatures, the Ic1 symbol may blink. You may

be able to use the camera if you remove the batter-

ies and warm them up.

and the batteries need lo be replaced.

1) When the power does not turn on.

2) When the 0 symbol blinks.

3) When the shutter does not release.

4) When film advance or rewind do not function.

5) When the Self-Timer does not function.

ing battery power, always turn the power off when

you are not taking pictures.

ver) for about 5 minutes, the power automatically

turns off, the LCD Panel display disappears and the

lens returns to the storage position. The purpose of

this function is to prevent waste of battery power.

The power will turn on again by operating any of the

buttons, dials or lever.

LOADING THE FILM

Always avoid direct sunlight when loading the film.

(Fig. 7)