Clas Ohlson DB300 Schnellstart-Handbuch

Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Zubehör Clas Ohlson DB300 herunter. Clas Ohlson DB300 4 Seiten. Wireless doorbell

Seite drucken
Clas Ohlson DB300 Schnellstart-Handbuch
Wireless Doorbell
Art.no 36-2382
Model DB300 + DBT501v
Please read the entire instruction manual before use and save it for future
reference. We reserve the right for any errors in text or images and for making any
necessary technical changes to this document. If you should have any questions
concerning technical problems please contact our Customer Services.
Product description
•
Cordless transmission
•
Simple configuration
•
Adjustable volume control
•
Range up to 60 metres
1
2
a
d
b
c
1.
Loudspeaker unit / receiver DB300
a)
[LEARN] button
b)
Volume control
c)
Electrical socket
2.
Pushbutton unit / transmitter DBT501V
d)
Light emitting diode
e)
Ring button
f)
Button for new code
Installation
Inserting the batteries
Loudspeaker unit requires no batteries. Pushbutton unit runs on
2x 1.5 V batteries (supplied).
1.
Remove battery shutter on reverse side of pushbutton unit and insert
the supplied batteries. Check that the poles are facing the right direction.
You can check that the batteries are correctly installed by pressing the button
– the batteries are correctly installed if the red light diode comes on.
2.
Press the button for new code.
3.
Put battery shutter back in place.
GREAT BRITAIN • for consumer contact, please visit www.clasohlson.co.uk and click on customer service.
Configuration
Configuration is essential for correct functioning of the units together.
Press
Reset the doorbell by removing the batteries from the pushbutton unit and then
replacing them.
1.
Connect loudspeaker unit to a wall socket.
2.
Check that the volume control is set on either HIGH or LOW.
3.
Keep [LEARN] pressed in and press ring button simultaneously (see fig.).
4.
When configuration is completed the loudspeaker unit will emit a signal on
pressing the ring button.
Note: If there has been a power cut or if the loudspeaker unit has been
unplugged from the wall socket, the pushbutton unit and the loudspeaker unit
will need to be reconfigured (see Configuration).
e
Mounting
Before you mount the doorbell you must insert the batteries and press the button
f
for a new code.
1.
Mark a place for the screw holes.
2.
Drill 2 holes and use raw plug if necessary.
3.
Screw in screws and hang pushbutton unit in place.
Trouble shooting
Problem
No signal from loudspeaker when
I press the ring button.
When I connect an apparatus
to the receiver the connected
apparatus does not function.
The units lose contact with
each other following a power cut
or if the loudspeaker unit has been
unplugged.
Disposal
Follow local ordinances when disposing of this product. If you are unsure about
how to dispose of this product contact your municipality.
Specifications
Power supply
Batteries
Range
Frequency
Hereby, Clas Ohlson AB, declares that following product(s):
Solution
• Reassemble doorbell.
See Configuration above.
• Check batteries and change
if necessary.
Check wall socket and make sure all
connections are correct.
The pushbutton unit and
the loudspeaker unit must be
reconfigured (see Configuration).
230 V AC, 50 Hz (loudspeaker unit)
2x 1.5 V batteries (pushbutton unit)
Up to 60 m in open spaces
433 MHz
Declaration of Conformity
Wireless Door Bell
36-2382 / DB-300, DBT501v
is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
Article 3.1a (Safety): EN 60065
Article 3.1b (EMC):
EN 301489-1
EN 301489-3
Article 3.2 (Radio):
EN 300220-1
EN 300220-3
0682
Insjön, Sweden, February 2011
Klas Balkow
President
Clas Ohlson, 793 85 Insjön, Sweden