esera automation 11134 Benutzerhandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Zubehör esera automation 11134 herunter. esera automation 11134 6 Seiten. Multisensor temperature, humidity and brightness for 1-wire bus system

Seite drucken
For rooms with permanently high air humidity values, such as saunas, we recommend the
1-Wire outdoor Temperature-Humidity Sensor (Art.No: 11135).
The living area Sensor is integrated into a 1-Wire Network via screwless pressure clamps or RJ45 plug
connection (CAT cable).
The living area Sensor is designed for cable entry from the rear or side. The housing cut-outs must be adapted to
the cable entry.
3
Technical Data
1-Wire Interface:
Measuring range
Temperature:
Accuracy Temperature:
Resolution:
Air humidity sensor:
Measuring range humidity:
Humidity accuracy:
Brightness sensor:
Measuring range:
Accuracy Lux:
Operating voltage:
Power consumption:
Connection:
4
Ambient conditions
Protection system:
Protection class:
Temperature, Operation:
Air humitidy:
Dimensions (outside):
5
Conformity
EN 50090-2-2
EN 61000-4-2, ESD
EN 61000-4-3, HF
EN 61000-4-4, Burst
EN 61000-4-5, Surge
EN 61000-6-1, Interference immunity
EN 61000-6-3, Interference radiation
RoHS
6
Software / Control
The living area sensor is read out via 1-Wire commands for DS18B20 and DS2438 devices and is supported by
many systems, such as ESERA 1-Wire Controller, ESERA 1-Wire Gateway, Loxone PLC, WAGO PLC (via
OWOS), OWFS, FHEM (Linux), IP-Symcon or microcontroller applications.
7
Control via 1-Wire Controller / 1-Wire Gateway
The control and data output of the 1-Wire outdoor sensor via the 1-Wire Controller / 1-Wire Gateway is very
simplified. The current sensor data is output continuously. No query of the data is necessary and available.
If you have assigned the article number (11134) of the OWD number of this sensor via ESERA Config Tool 3,
you will henceforth receive data sets adapted to the sensor. Thus, no further formulas are necessary.
7.1
Data output 1-Wire Controller / 1-Wire Gateway
The following data formats are output for the ESERA-Automation modules. If you divide the value by 100, you get
the data with two decimal places.
Data output
1_OWD1_1|2008
1_OWD1_2|511
1_OWD1_3|850
1_OWD1_4|1200
1_OWD1_5|80000
Further information on the possibilities and commands can be found in the current programming manual of the 1-
Wire Controller /1-Wire Gateway, which can be found within Config Tool 3.
All rights reserved. Reproduction as well as electronic duplication of this user guide, complete or in part, requires the written consent of
ESERA GmbH. Errors and technical modification subject to change. ESERA GmbH, ESERA-Automation 2020
www.esera.de
DS2438, Multisensor for temperature, humidity, brightness and operating voltage
-30°C to +60°C (sensor element: -55°C to +125°C)
+/- 0.5° in the range from -10°C to + 85°C
9 bit, 0.03125°C/ bit depending on the selected resolution
Capacitive sensor of the manufacturer Honeywell
0-100% rel. humidity
+/-3.5 % (10-85% rH), +/-7% (<10% and >85% rH)
Sensor, adapted to the sensitivity of the human eye
2 - 7000 Lux
+/-25% in the range up to approx. 200 Lux, +/-15% in the range up to 7000 Lux
5 V= (+/-10%)
approx. 2 mA
push-in terminal and RJ45 modular socket
IP20
III
-25°C to 80°C
10 - 90% (non condensing)
71 x 71 x 32mm (L x W x H)
=> Controller No._Module No._Data set|Temperature (°C) example: 20,08 °C
=> Controller No._Module No._Data set|Voltage VCC (V)
=> Controller No._Module No._Data set|Air humitidy (rF) example: 85,0%
=> Controller No._Module No._Data set|Dew point (°C) example: 12,00 °C
=> Controller No._Module No._Data set|Brightness (Lux) example: 800,00 Lux
11134 V2.0 R1.0 Manual
Page 2 of 6