esera automation 11151 Benutzerhandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Zubehör esera automation 11151 herunter. esera automation 11151 8 Seiten. 1-wire sensor for temperature, humidity and air quality w/auto-e-connect

Seite drucken

Thanks to the generous ventilation openings, the 1-Wire Multisensor Pro I very directly detects the ambient

conditions in rooms.

The 1-Wire Multisensor Pro I has a warm-up time for the air quality value. With a new 1-Wire Multisensor,

this warm-up time is approx. 15 hours. After initial start-up, this is reduced to minutes or hours, depending on

how long the Multisensor was without power. The warm-up phase is indicated by the red LED flashing.

During the warm-up period, the air quality is output with the value 0. For further details, see chapter

"commissioning and warm-up".

The 1-Wire Multisensor Pro I is equipped with screw terminals for the electrical connection of the 1-Wire bus

interface and can be operated in standard mode (3 cables for ground, data and 5V).

Due to the use of high-quality internal sensors with 12-bit resolution, the 1-Wire Multisensor Pro II delivers

very accurate values for temperature, relative humidity and air quality. In addition, the evaluation of the

delivered measured values is enormously simplified.

Auto-E-Connect® Support

The ESERA Auto-E-Connect® 1-Wire Plug and Play system will be used for the

1-Wire Bus supported. This enables fully automatic configurations of 1-Wire sensors

and actuators on the 1-Wire bus. It is optimized for industrial applications and

enables significant added value beyond the sensor and chip data.

The Auto-E-Connect function automatically recognizes ESERA chips, sensors and actuators, starts suitable

libraries and outputs fully formatted data.

The Auto-E-Connect functionality will be available from mid 2020 via 1-Wire Controllers, 1-Wire Gateways and

1-Wire ECO from ESERA available.

Further information on ESERA Auto-E-Connect can be found on the ESERA website, ESERA Config-Tool 3,

or in the download area for this article in the ESERA Webshop

Technical data

Function:

Temperature sensor:

Range of measuring temp.: -40°C to +60°C (sensor element: -40°C to +85°C)

Accuracy temperature:

Resolution:

Humidity sensor:

Range of measuring hum.: 0-100% rel. humidity

Accuracy humidity:

Data output:

Air quality sensor (VOC):

Range of measuring:

Accuracy:

Data output:

1-Wire connection:

Connection:

1-Wire interface

Operation voltage:

Current consumption:

Connection:

Ambient conditions

Protection system:

Protection class:

Operation temperature for temperature sensor and rel. Humidity sensor:

Air quality sensor:

Rel. humidity:

Storage temperature:

Outer dimensions:

ESERA GmbH. Errors and technical modification subject to change. ESERA GmbH, ESERA-Automation 2020

www.esera.de

Multisensor for temperature and rel. humidity and air quality,

monitoring of operating voltage

Precise digital temperature sensor with 12 Bit measurement resolution

0,3° in the range of -10°C - 60°C (more accurate than the DS18B20 sensor)

12 Bit, 0,06°C/Bit depending on selected resolution

Capacitive digital humidity sensor with high accuracy

+/-3 % in the range of 10-85% rel. humidity

0-10V equates 0-100% rel. humidity, 0,1V = 1% rF

Mixed gas sensor (VOC)

400 - 1800 ppm (CO2 equivalent)

+/- 10%, depending on air composition

30-250mV equates 400-2900ppm, 1mV output voltage equates 11,6ppm.

Min. output value: 30,51mV equates 405ppm.

3 – conductor connection (data, ground and 5V, parasitic operation not

supported)

Screw terminals

Basis DS2438

5 V= (+10%/-20%)

ca. 45mA

Screw terminals

IP20

III

-25°C to 50°C, (limitation of the max. temperature by rel. humidity sensor and

sensor-housing)

0 to 50°C

5 - 95% (non-condensing)

-25 to 50°C

71 x 71 x 32mm (LxWxH)

11151 V2.0 R1.0 Manual

Page 2 of 8