ClearCube CD7424SFPST Schnellstart-Handbuch - Seite 3
Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Server ClearCube CD7424SFPST herunter. ClearCube CD7424SFPST 3 Seiten. Zero client
Seite drucken1. Connect a USB keyboard and a mouse to the USB ports on the
front or on the rear of the zero client.
2. Connect an appropriate network cable to the SFP module
located on the rear of the zero client, and then connect the other
end of the cable to the appropriate network infrastructure
device (such as a fiber network switch or a fiber transceiver).
NOTE:
The zero client is set to forced full-duplex mode with
flow control (Link Fault Passthrough) disabled.
These settings should be the same on any network
switch to which the zero client connects. Check
your switch settings and make any necessary
changes (see "Network Settings" below for
information about configuring Cisco switches).
3. Connect a monitor cable to each DVI-I port on the rear of the
zero client. If you are using VGA monitors, attach DVI
adapters to your monitor cables.
4. Connect the AC power adapter to the power cable (both are
included with the zero client).
5. Connect the power adapter to the rear of the client, and then
plug the power cable into a power outlet. See "Buttons and
Indicators" for information about powering the zero client on
and off.
NOTE: You can enable a zero client to receive an IP address from
a DHCP server. If a DHCP server does not assign an
address within a designated timeout period, the zero client
uses a default, fallback IP address. If you use these default
addresses and have DHCP enabled, you must wait 120
seconds before you can connect to a host. If you use the
direct connect methodology in your environment,
ClearCube recommends disabling the client's DHCP
setting to eliminate the need to wait 120 seconds before
connecting. See PCoIP System User's Guide at
www.clearcube.com/support
See "Configuration Steps and Additional Information" for more
information.
WEEE Disposal Guidelines
In the European Union, this electronic product is under European Directive (2002/96/EC) WEEE. When this product reaches the end of its useful life or is
no longer used, do not discard it with conventional waste. Recycle this product at an approved, designated recycling or treatment facility. Check with local
authorities for proper disposal instructions. For assistance, contact
ClearCube Technology
for more information.
8834 Capital of Texas Hwy N
Network Settings
The CD7424SFPST zero client is set to:
•
Forced, full-duplex mode, 1000 Mbps
•
Flow control (Link Fault Passthrough) disabled
These settings should be the same on any network switch to which
the zero client connects. Check your switch settings and make any
necessary changes.
The following example shows how to configure negotiation and
flow control settings on Cisco Catalyst
CD7424SFPST zero clients (note that these commands are not
applicable to Cisco Nexus
router# configure terminal
router(config)# interface gigabitethernet 0/1
router(config-if)# no negotiation auto
router(config-if)# flowcontrol send off
router(config-if)# flowcontrol receive off
router(config-if)# end
router#
If you use different switches in your environment, perform
equivalent commands to disable auto-negotiation and flow control.
Configuration Steps and Additional Information
See PC-over-IP System User's Guide and PCoIP Firmware Support
and Compatibility Guide at
information about zero client deployment, configuration, and
administration. If you are using ClearCube Sentral in your
environment, see Sentral Administrator's Guide for information
about connection brokering, device administration, and more.
Web site:
www.clearcube.com/support
Email:
Toll-free:
(866) 652-3400
Phone:
(512) 652-3400
Austin, Texas 78759
voice 512 652 3500 www.clearcube.com
switches to connect with
®
switches).
®
www.clearcube.com/support
G0200150 Rev A
for