esera automation 11308 Benutzerhandbuch - Seite 4
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Adapter esera automation 11308 herunter. esera automation 11308 5 Seiten. 1-wire bus coupler ethernet
Seite drucken
10
Assembly
The module may only be operated at the specified voltages and ambient conditions. The device is
intended for installation inside a control cabinet as a stationary device.
11
Disposal note
Do not dispose of the device within the household waste!
According to the directive concerning old electrical and electronic appliances, electronic devices
must be disposed of via the collecting points for old electronic
appliances!
12
Safety instructions
When using products that come into contact with electrical voltage, the valid VDE regulations must be observed, especially
VDE 0100, VDE 0550/0551, VDE 0700, VDE 0711 and VDE 0860
•
All final or wiring work must be carried out with the power turned off.
•
Before opening the device, always unplug or make sure that the unit is disconnected from the mains.
•
Components, modules or devices may only be put into service if they are mounted in a contact proof housing.
During installation they must not have power applied.
•
Tools may only be used on devices, components or assemblies when it is certain that the devices are
disconnected from the power supply and electrical charges stored in the components inside the device have been
discharged.
•
Live cables or wires to which the device or an assembly is connected, must always be tested for insulation faults
or breaks.
•
If an error is detected in the supply line, the device must be immediately taken out of operation until the faulty
cable has been replaced.
•
When using components or modules it is absolutely necessary to comply with the requirements set out in the
accompanying description specifications for electrical quantities.
•
If the available description is not clear to the non-commercial end-user what the applicable electrical
characteristics for a part or assembly are, how to connect an external circuit, which external components or
additional devices can be connected or which values these external components may have, a qualified electrician
must be consulted.
•
It must be examined generally before the commissioning of a device, whether this device or module is basically
suitable for the application in which it is to be used.
•
In case of doubt, consultation with experts or the manufacturer of the components used is absolutely necessary.
•
For operational and connection errors outside of our control, we assume no liability of any kind for any resulting
damage.
•
Kits should be returned without their housing when not functional with an exact error description and the
accompanying instructions. Without an error description it is not possible to repair. For time-consuming assembly
or disassembly of cases charges will be invoiced.
•
During installation and handling of components which later have mains potential on their parts, the relevant VDE
regulations must be observed.
•
Devices that are to be operated at a voltage greater than 35 VDC / 12mA, may only be connected by a qualified
electrician and put into operation.
•
Commissioning may only be realized if the circuit is built into a contact proof housing.
•
If measurements with an open housing are unavoidable, for safety reasons an isolating transformer must be
installed upstream or a suitable power supply can be used.
•
After installing the required tests according to BGV A3 / Betriebssicherheitsverordnung must be performed.
13
Warranty
ESERA-Automation (E-SERVICE GmbH) guarantees that the goods sold at the time of transfer of risk to be free from
material and workmanship defects and have the contractually assured characteristics. The statutory warranty period of two
years begins from date of invoice. The warranty does not extend to the normal operational wear and normal wear and tear.
Customer claims for damages, for example, for non-performance, fault in contracting, breach of secondary contractual
obligations, consequential damages, damages resulting from unauthorized usage and other legal grounds are excluded.
Excepting to this, ESERA-Automation accepts liability for the absence of a guaranteed quality resulting from intent or gross
negligence. Claims made under the Product Liability Act are not affected.
If defects occur for which the ESERA-Automation is responsible, and in the case of replacement goods, the replacement is
faulty, the buyer has the right to have the original purchase price refunded or a reduction of the purchase price. ESERA-
Automation accepts liability neither for the constant and uninterrupted availability of the ESERA-Automation or for technical
or electronic errors in the online offer.
All rights reserved. Reproduction as well as electronic duplication of this user guide, complete or in part, requires the written consent of
ESERA-Automation or E-Service GmbH. Errors and technical modification subject to change.© ESERA-Automation, E-Service GmbH 2019
www.esera.de
11308 V1.0 R1.0 Manual
Page 4 of 5