esera automation 19200 Linux Handbuch - Seite 8

Blättern Sie online oder laden Sie pdf Handbuch für Aufnahmegeräte esera automation 19200 Linux herunter. esera automation 19200 Linux 9 Seiten.

Seite drucken

ESERA Skins for IP-Symcon

We provide three different green Skins via github server

Dark Green

https://github.com/ESERA-Automation/ESERA-skin-dark-green.git

ESERA Green

https://github.com/ESERA-Automation/ESERA-skin-green.git

ESERA-british-racing-green

https://github.com/ESERA-Automation/ESERA-british-racing-green.git

Assembly

The installation site must be protected from moisture. The device may only be used in dry

indoor rooms. The device is intended for mounting inside a switch cabinet as a stationary

device.

Disposal note

Do not dispose of the device in household waste! Electronic devices must be disposed of

the directive on waste electrical and electronic equipment on local

Collection points for electronic waste must be disposed of!

Sicherheitshinweise

When using products that come into contact with electrical voltage, the valid VDE regulations must be observed, especially

VDE 0100, VDE 0550/0551, VDE 0700, VDE 0711 and VDE 0860



All final or wiring work must be carried out with the power turned off.



Before opening the device, always unplug or make sure that the unit is disconnected from the mains.



Components, modules or devices may only be put into service if they are mounted in a contact proof housing.

During installation they must not have power applied.



Tools may only be used on devices, components or assemblies when it is certain that the devices are disconnected

from the power supply and electrical charges stored in the components inside the device have been discharged.



Live cables or wires to which the device or an assembly is connected, must always be tested for insulation faults or

breaks.



If an error is detected in the supply line, the device must be immediately taken out of operation until the faulty cable

has been replaced.



When using components or modules it is absolutely necessary to comply with the requirements set out in the

accompanying description specifications for electrical quantities.



If the available description is not clear to the non-commercial end-user what the applicable electrical characteristics

for a part or assembly are, how to connect an external circuit, which external components or additional devices can

be connected or which values these external components may have, a qualified electrician must be consulted.



It must be examined generally before the commissioning of a device, whether this device or module is basically

suitable for the application in which it is to be used.



In case of doubt, consultation with experts or the manufacturer of the components used is absolutely necessary.



For operational and connection errors outside of our control, we assume no liability of any kind for any resulting

damage.



Kits should be returned without their housing when not functional with an exact error description and the

accompanying instructions. Without an error description it is not possible to repair. For time-consuming assembly or

disassembly of cases charges will be invoiced.



During installation and handling of components which later have mains potential on their parts, the relevant VDE

regulations must be observed.



Devices that are to be operated at a voltage greater than 35 VDC / 12mA, may only be connected by a qualified

electrician and put into operation.



Commissioning may only be realized if the circuit is built into a contact proof housing.



If measurements with an open housing are unavoidable, for safety reasons an isolating transformer must be

installed upstream or a suitable power supply can be used.



After installing the required tests according to DGUV / regulation 3 (German statutory accident insurance,

https://en.wikipedia.org/wiki/German_Statutory_Accident_Insurance) must be carried out.

Warranty

ESERA GmbH guarantees that the goods sold at the time of transfer of risk to be free from material and workmanship

defects and have the contractually assured characteristics. The statutory warranty period of two years begins from date of

invoice. The warranty does not extend to the normal operational wear and normal wear and tear. Customer claims for

damages, for example, for non-performance, fault in contracting, breach of secondary contractual obligations,

ESERA GmbH. Errors and technical modification subject to change. ESERA GmbH, ESERA-Automation 2020

www.esera.de

19200 V1.0 R1.0 Commissioning II

Page 8 of 9