DIW DPM-3500 Betriebsanleitung - Seite 2

Blättern Sie online oder laden Sie pdf Betriebsanleitung für Kontrolleinheit DIW DPM-3500 herunter. DIW DPM-3500 2 Seiten. Power module

Seite drucken

Operating instructions power module

DPM-3500

(RSW8830R)

Intended Use:

The radio power switch DPM-3500 can be switched on and off wirelessly

with a suitable radio remote switch (all transmitters of the DIW radio

system). Due to the small design, the switch is particularly suitable for

installation behind sockets in order to make them remotely switchable.

The DPM-3500 is only suitable for operation with a mains voltage of up to

230 V/AC, 50 Hz and must be installed and operated in a suitable flush-

mounted or surface-mounted box. It can be connected to a 3500W resistive

load and a 600W inductive load. Ohmic loads arise primarily with

consumers that fulfill their functions through electrical resistance.

Consumers with a predominantly ohmic load are, for example,

incandescent lamps. Consumers with an inductive load are, for example,

motors, energy-saving lamps, etc. These contain coils that generate

inductive and electrical resistance that counteract the flow of current. Use is

only permitted inside. Contact with moisture, e.g. in the bathroom, must be

avoided at all costs.

Be sure to observe the safety instructions!

Connection

1. Connect the device you want to switch to the two inner terminals of

the receiver switch; see the schematic on the right.

2. The "N" terminal is the neutral wire; the "X" connection is the switched

output/phase/L.

3. The outer connections with the two pressure clamps are for the

connection to the mains ("N" = neutral conductor, "L" = phase).

4. The built-in wireless switch "DIW-Funk" Mini Power Module 3500 W is

intended for direct installation in a flush-mounted or surface-mounted

box.

5. During assembly, make sure that the button on the back of the

housing is exposed and not accidentally pressed.

6. The button on the back of the housing is used (among other things) to

program the receiver switch for connection to a radio transmitter of the

"DIW radio" system. Observe the following sections before you seal

the flush-mounted or surface-mounted box and put the product into

operation

Operation

a) Teaching in the receiver switch for a remote control

The receiver switch can be taught in such a way that it connects to a

radio transmitter of a "DIW radio" system, e.g. B. with a wall

transmitter or a radio remote control. Pay attention to the

information in the operating instructions for the transmitter you are

using.

Up to 8 different radio transmitters of the "DIW radio" system can be

taught. The receiver switch can then be turned on or off from

various locations.

Complete the following steps to learn the switch:

=> Usage Scenario:No radio codes saved

1. Connect the receiver switch to the mains. The LED display (2) starts flashing red; the receiver switch

is in learning mode.

2. Press the "ON" button on the "DIW radio" transmitter. Press and hold the "DIW Funk" radio

transmitter button until the LED indicator next to the receiver switch button stops flashing. The radio

code for this transmitter is now recognized and saved.

3. The learning process is completed successfully, the device automatically exits the learning mode.

=> Usage scenario: radio code/s already gesaved

1. Connect the receiver switch to the mains. The LED display does not flash. Press and hold the

receiver switch button (1) until the LED indicator (2) starts flashing. The receiver switch is now in

learning mode for a new auxiliary code.

2. Press the "ON" button on the "DIW-Funk" radio transmitter. Press and hold the "ON" button on the

"DIW Funk" transmitter until the LED display next to the button on the receiver switch stops flashing.

The radio code for this transmitter is now recognized and saved.

3. The learning process is completed successfully, the device automatically exits the learning mode.

4. Repeat these configuration steps to store more "DIW Funk" stations until the maximum number of

stations that can be stored is reached.

b) Deleting stored radio transmitters from the receiver switch

You can delete all radio codes at the same time, or if you want to use the switching channel of a

radio transmitter (wall switch or radio remote control) for another receiver switch, the switching

channel can be deleted individually.

=> Application scenario: Delete all radio codes

1. When the receiver switch has turned off the device, press the button until the LED indicator (2) starts

flashing. The receiver switch is now in learning mode.

2. Release the switch, press again and hold until the LED indicator (2) turns off. All stored radio codes

are now deleted.

=> Application scenario: Deleting a single radio code

1. Press and hold the receiver button (1) until the indicator LED (2) starts flashing.

2. Press and hold the Channel OFF button (the button to which the channel is assigned) on your

remote control until the indicator LED turns off.

c) Switch on and off with the button on the receiver switch

For a function test, the device connected to the receiver switch can also be switched on and off with

the button.

Briefly press the button on the receiver switch to switch the device on (the LED on the receiver

switch lights up) or off (the red LED goes out).

Technical specifications:

Operating voltage..........: 230V/ 50 Hz

Switching capacity................: 3500 W (resistive load) + 600 W (inductive load)

Operating temperature........: 0°C to +35°C

Dimensions, weight....: 41 x 41 x 18mm, 32g

Suitable for all - transmitters and many compatible brands.

Reproductions of any kind require the written permission of the publisher.