Altox Timer-2 Betriebshandbuch - Seite 4

Blättern Sie online oder laden Sie pdf Betriebshandbuch für Zeitschaltuhr Altox Timer-2 herunter. Altox Timer-2 4 Seiten.

Seite drucken

Display of time, voltage and temperature

The heater is started: To display the remaining operating time of the

heater, press the "<" or ">" button.

Then, to display the current time, press the "P" button.

The heater is stopped: To display the current time, press the "<" or ">"

button. In this section of the menu, pressing the "<" or ">" buttons will

display the seconds value of the current time.

Subsequent pressings of the "P" button switch to the voltage display

section, and then to the car parking heater temperature display section.

In the last section, to turn oﬀ the display, press the "P" button.

Примечание: The value of the car parking heater temperature is only

available on the part of the Eberspacher and Webasto digital heaters. If

the temperature value is not available, the menu section will be skipped.

Programming the timer

Three programmable timers are available to the user.

Each of the timers has two modes of operation:

— Single mode for switching on day ahead;

— Weekly mode of daily switching on for 7 days ahead.

Note: After 6 starts, the weekly mode automatically goes into single-turn

mode.

To view the status of the timer (activated or deactivated), in the standby

mode (the display is oﬀ), you must press the "P" button one, two or three

times, the display will show the timer number "-1t-"

"-2t-" or "-3t-", respectively.

The status of the timer is determined by the number of points in the right

corner:

— No points: the timer is deactivated

— One point: the timer is activated in the single-turn mode

— Two points: the timer is activated in a weekly mode

Activate / deactivate the timer and change the timer mode in the current

menu with the

button.

To change the timer settings, press the "<" or ">" button, the display will

show the start time of the heater.

Press the "<", ">" and "P" buttons to set the desired start time of the heater,

then set the operating time of the heater "t:30" from 10 to 99 minutes.

After pressing "P", the settings will be saved and the timer will be

activated in the single-turn-on mode for the day ahead.

Note: in the timer "-1t-" setting menu, the stored operating time of the

heater "t:30" is the default start time from the direct-on button

from the external pulse signal at the INPUT input.

Diagnostics of the heater

The menu is only available when controlling digital types of heaters.

In standby mode (the display is oﬀ), press and hold the ">" button and

additionally press the

diagnostics mode of the heater, press "P" in addition.

The display will show "FX:YY", where X is the number of the cell with the

error code, YY is the error code.

If there are no errors, YY takes the value "-".

To switch between the available cells with error codes, use the "<" and ">"

buttons. To delete all errors, press and hold the

If the Eberspacher heater is diagnosed, then pressing the "P" button will

move the current fault menu to the saved section from the menu and

display "EX:YY" with the same parameters.

To turn oﬀ the display, press "P" in addition.

Note: description of error codes by the link https://altox.ru/en/docs/

Select heater type

In standby mode (the display is oﬀ), press and hold the "<" button and

additionally press ">". The display will show "H:XY", where X and Y are the

type of heater and digital protocol (default type is A0).

Set the required type of heater and digital protocol by pressing the "<" and

">" buttons, following the description:

Automatic/Analogue:

A0 - automatic detection of the digital type of heater

A1 - heater with analogue signal control

Eberspacher:

Е1 - Aftermarket + Hydronic II

E2 - Factory-installed Hydronic II (Toyota, VW)

E3 - Factory-installed Hydronic II (Audi, Land Rover, VW)

E7 - Ventilation (Aftermarket)

Webasto Thermo Top:

t1 – Thermo Top C/Z/V/EVO/VEVO

t2 – Thermo Top V/VEVO

t3 – Emulation WTT

t4 – Emulation Timer 1533

t5 – Emulation Telestart (ver.1)

t6 – Emulation Telestart (ver.2)

t7 – Ventilation (summer mode)

The selected type of heater is stored in memory after pressing "P".

, and

Note: automatic determination of the type Eberspacher and Webasto

digital heater (mode A0) occurs at the ﬁrst start.

button. The display will show "-Hd-", to enter the

button for 3 seconds.