dji Focus Schnellstart-Handbuch - Seite 2

Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Fernsteuerung dji Focus herunter. dji Focus 2 Seiten. Accessory support frame
Auch für dji Focus: Schnellstart-Handbuch (2 seiten), Schnellstart-Handbuch (6 seiten)

Seite drucken

DJI FOCUS

Quick Start Guide

Install the Antenna

Screw on the antenna.

Mount the Motor

To mount the motor onto your camera support rod:

1. Loosen the knob on the quick-release mount

and slide the motor onto the support rod.

The motor gear can be mounted on either side of the

●

motor. To remove the gear, loosen the knob at the

center of the gear.

The motor supports a 15 mm rod diameter by default.

●

To mount it on a 19 mm rod, slide the step-down

adapters off the clamp.

2. Tighten the knob, ensuring that the motor gear

and lens gear ring make good contact.

3. Connect the communication port on the motor

to an external power source using the supplied

power cable. If you are using the Ronin-M,

connect the motor to the P-TAP Accessory

power port on the Ronin-M.

DJI Focus can work in wireless mode or cable mode. To

use cable mode, connect the communication ports on

the remote controller and motor using the data cable.

Ensure the motor is mounted firmly.

●

DO NOT touch the motor when it is rotating.

●

Cable mode will take precedence over wireless mode.

●

Attach the Neck Strap

Insert the neck strap connector

while pulling on the button.

Ensure the neck strap is attached securely.

●

Calibrate the Motor

Turn on the remote controller by holding down the

power button for 2 seconds.

If your camera lens has mechanical limits, use Auto

calibration. Otherwise, use Manual-Remote or

Manual-Hand calibration.

50.0%

Calibrate

Auto

Select Calibrate > Auto (Shortcut: Press the 'A' and

'B' buttons together). The motor gear will rotate in

both directions in turn to locate the mechanical

limits of your camera lens. When the calibration is

complete, select Back to apply the calibration or

Stop to cancel.

Manual-Remote

Select Calibrate > Manual-Remote > Start to

begin. Press the up arrow to rotate the lens in one

direction, and select OK when it reaches the desired

upper limit. Next, press the down arrow to rotate

the lens in the other direction, and select OK when it

Motor Power Cable

reaches the desired lower limit.

The motor will automatically reserve a 1mm margin at both mechanical limits for protection.

●

Mount the Lens Gear Ring

Used with the Zenmuse X5

DJI Focus is fully compatible with the Zenmuse X5 series gimbal and camera. To allow communication

between the two devices, connect the communication port on the Focus remote controller to the

CAN Bus port on the Inspire 1 remote controller using the dedicated CAN Bus cable.

Select Menu > Aperture > On to enable the Aperture Control.

To switch from focus control to aperture control, press the 'D' button and then follow the instructions in

the DJI GO app to operate the focus wheel.

Ensure that the Zenmuse X5 camera is set in AF mode.

●

The remote controller overrides the in-app controls. You will not be able to adjust the focus or aperture in the DJI GO app.

●

You can purchase the dedicated CAN Bus cable on the DJI Store.

●

Basic Operation

Manual-Hand

Select Calibrate > Manual-Hand >

Start to begin. Rotate the lens

Turn the focus wheel to control the focus,

manually to the desired upper and

zoom or iris of your camera lens.

lower limits of your camera lens,

and select OK to confirm the limits.

Refer to the user manual for more information.

http://www.dji.com/product/focus

※This Quick Start Guide is subject to change without prior notice.

Mount the lens gear ring if you are not

using a cinema lens with gear rings.

1. Choose the lens gear ring that best fits

your camera lens.

2. Tighten the screw.

Ensure that the lens gear ring and camera lens

●

make good contact.

Ensure the lens gear ring screw is installed

●

properly to allow an unobstructed full range of

motion.