djm direct DJMSL8 Übersetzung der Originalbetriebsanleitung - Seite 4
Blättern Sie online oder laden Sie pdf Übersetzung der Originalbetriebsanleitung für Säge djm direct DJMSL8 herunter. djm direct DJMSL8 14 Seiten.
Seite drucken
·Use correctly sharpened blades and observe the maximum speed
marked on the blade.
·Do not remove any cut-offs from the cutting area until the guard is
fully locked in place and the blade has come to rest.
·Ensure that the mitre saw is fixed to a work bench wherever
possible.
·When cutting long pieces which extend well over the table width
ensure that the ends are adequately supported at the same height as
the saw table top. Supports should be positioned in such a way to
ensure that the workpiece does not fall to the ground. once the cut
has been made. A number of supports at regular intervals may be
required if the workpiece is extremely long.
5. NOT INTENDED USE
If not intended use the risk of fire, electric shock and personal injury
maybe further and
- The provisions contained in this guarantee are not intended to limit,
modify, take away from, disclaim or exclude any statutory guarantee
set forth in any applicable provincial or federal legislation.
6. RESIDUAL RISKS
Even if you use this electric power tool in accordance with
instructions, certain resi dual risks cannot be rules out. The
following hazards may arise in connection with the equipment's
construction and layout:
1. Lung damage if no suitable protective dust mask is used.
2. Damage to hearing if no suitable ear protection is used.
3. Health damage caused by hand-arm vibrations if the equipment is
used over a prolonged period or is not properly guided and
maintained.
7.GENERAL SAFETY INSTRUCTIONS
WARNING ! When using electric tools basic safety precautions
should always be followed to reduce the risk of fire, electric shock
and personal injury including the following.
Read all these instructions before attempting to operate this product
and save these instructions.
1 - Keep work area clear
- Cluttered areas and benches invite injuries.
2 - Consider work area environment
- Do not expose tools to rain.
- Do not use tools in damp or wet locations.
- Keep work area well lit.
- Do not use tools in the presence of flammable liquids or gases.
3 - Guard against electric shock
- Avoid body contact with earthed or grounded surfaces (e.g. pipes,
radiators, ranges, refrigerators).
4 - Keep other persons away
- Do not let persons, especially children, not involved in the work
touch the tool or the extension cord and keep them away from the
work area.
5 - Store idle tools
- When not in use, tools should be stored in a dry locked-up place,
out of reach of children.
6 - Do not force the tool
- It will do the job better and safer at the rate for which it was
intended.
7 - Use the right tool
- Do not force small tools to do the job of a heavy duty tool.
- Do not use tools for purposes not intended; for example do not
use circular saws to cut tree limbs or logs.
8 - Dress properly
- Do not wear loose clothing or jewellery, they can be caught in
moving parts.
- Non-skid footwear is recommended when working outdoors.
- Wear protective hair covering to contain long hair.
9 - Use protective equipment
- Use safety glasses.
- Use face or dust mask if working operations create dust.
10 - Connect dust extraction equipment
- If the tool is provided for the connection of dust extraction and
collecting equipment, ensure these are connected and properly
used.
11 - Do not abuse the cord
- Never yank the cord to disconnect it from the socket. Keep the
cord away from heat, oil and sharp edges.
12 - Secure work
- Where possible use clamps or a vice to hold the workpieces. It is
safer than using your hand.
13 - Do not overreach
- Keep proper footing and balance at all times.
14 - Maintain tools with care
- Keep cutting tools sharp and clean for better and safer
performance.
- Follow instruction for lubricating and changing accessories.
- Inspect tool cords periodically and if damaged have them repaired
by an authorized service facility.
- Inspect extension cords periodically and replace if damaged.
- Keep handles dry, clean and free from oil and grease.
15 - Disconnect tools
- When not in use, before servicing and when changing
accessories such as blades, bits and cutters, disconnect tools from
the power supply.
3