Clemas & Co TENNANT F3 Benutzerhandbuch - Seite 6

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Sander Clemas & Co TENNANT F3 herunter. Clemas & Co TENNANT F3 6 Seiten. Polisher

Seite drucken

•

When transporting the machine in lifts, put the shaft/bar in a verti-

cal position so that it cannot catch on the lift walls.

•

The shaft/bar is automatically secured against recoil by the pat-

ented shaft/bar adjustment unit.

•

Only the spray and cleaning agents suitable for the machine's

purpose may be used.

•

Never use highly flammable, combustible, toxic, health-hazardous,

corrosive or irritant substances.

•

Repairs, including the fitting of spray agent lines and hoses, may

only be carried out by approved customer service shops or by

Trouble Shooting

Problem

Machine does not operate

Machine operates with a wobble

or jerky motion.

Machine circuit breaker trips

continuously.

Technical specifications

A.C. motor

Rated power

Max. amp draw

Brush (rpm)

Brush (mm)

Working height (mm)

Working weight

Protection class

Belt-driven

Sound pressure level LPA

Weighted acceleration value

Model: F3,F8,F12

Tennant N.V.

Adress: Industrielaan 6, 6405 AB

P.O. Box 6, 5400 AA Uden-The Netherlands

Uden/Netherlands, 20-12-06

-----------------------------------------------------------------

Richard van de Hoogen - Technical Support Engineer

Cause

Faulty power cord.

Tripped circuit breaker

Faulty machine wiring.

Faulty motor.

Capacitor burned out

Soiled Pad.

Improper pad/brush for application.

Pad driver/brush not installed correctly.

Pad/brush unevenly worn.

Pad not properly centered on pad driver

Heavily soiled pad/brush

Improper pad/brush for application

Defective circuit breaker.

Worn carbon brushes in motor.

F3 low speed

230 V: 50 Hz

1000 W

5,5 A

165

430

250

31 kg

lPx4

59db (A)

1.05 m/sec2

DECLERATION OF CONFORMITY FOR MACHINERY (Directive 89/392/EEC, Annex II, sub A)

Machine nr.: MF122004, MF122904, MF32004, MF32904, MF82004, MF82904

Herewith declares, on our own responsibility, that the machinery

- is in conformity with the provisions of Directive 89/392/EEC, 73/23/EWG and 89/336/EWG

- The following standards and normative documents have been applied:

EN 60335-1 (ed.3);am1;am2, 60334-2-67(ed2);am1, EN60355-1:94+A1:96+A12:96+A13:98+A14:

98+A15:00+A2:00+A16:01,EN60355-2-67:98+A1:00, EMC:CISPR 14-1:00+A1:01,CISPR 14-2:01,

ICE61000-3-2:00,IEC61000-3-3:94+A1:01,EN55014-1:00+A1:01,EN 55014-2:97+A1:01,

EN61000-3-2:00, EN 61000-3-3:95+A1:01

Home

Find...

specialists in this field who are familiar with all the relevant safety

regulations.

Storage

•

Remove brush/pad driver from machine and neatly coil cord

around cord hook and handle.

•

Store the machine in a dry place and in normal room conditions

(not below under 0°C).

Solution

Contact Service Center.

Wait 10 min. till machine cooled down and try again.

Contact Service Center

Replace Pad

Change to proper pad/brush

Remove and reinstall pad driver/brush

Replace pad/brush

Remove and reinstall pad driver

Clean or replace pad/brush

Change to proper pad/brush

Contact Service Center

F8 high speed

230 V; 50 Hz

1100 W

5,5 A

400

430

250

31 kg

lPx4

59db (A)

1.05 m/sec2

- 6 -

Go To..

F12 Duo speed

230 V, 50 Hz

1200/1500 W

5,2 / 8,1 A

170 / 340

430

250

37 kg

IPx4

65db

1.05 m/sec2