Altronix AL1042ULADA Anwendungshandbuch - Seite 6

Blättern Sie online oder laden Sie pdf Anwendungshandbuch für Extender Altronix AL1042ULADA herunter. Altronix AL1042ULADA 8 Seiten. Nac power extenders
Auch für Altronix AL1042ULADA: Installationshandbuch (17 seiten), Installationshandbuch (3 seiten), Anwendungshandbuch (8 seiten)

Seite drucken

Outputs must be programmed independently (OUT1 - OUT4)

Switch Positions

Function

Input to Output

Follower Mode

Temporal

Code 3 Mode

Steady Mode

For the above modes DIP Switch 4 determines which Input controls the corresponding output:

Switch 4 in the ON position causes output(s) to be controlled by Input 1.

Switch 4 in the OFF position causes output(s) to be controlled by Input 2.

Note: It is required to control visual notification appliances (strobes) via

Input 1 (IN1) and audible notification appliances (horns) via Input 2 (IN2).

This allows audible notification appliances (horns) and visual notification

appliances (strobes) to be silenced/ deactivated at same time.

The FACP must be capable of a visual annunciation to the silencing status of

the output or zone(s) to which the AL1042/R1042ULADA (NAC Power Extender) is connected.

Function

Amseco

Sync Mode*

Gentex

Sync Mode*

Gentex is a registered

trademark of

Gentex Corporation.

System Sensor

Sync Mode*

System Sensor is a

registered trademark

of Honeywell.

CooperWheelock

Sync Mode*

CooperWheelock is a

registered trademark

of Cooper Wheelock.

*Note: AL1042ULADA, R1042ULADA will only synchronize horns, horn/strobes, and strobes that contain

synchronization capability. The same synchronization mode must be selected for all outputs.

- 6 -

Output Programming Selection Table:

Descriptions

OFF

Output follows signal it receives from the corresponding input (i.e. FACP

2, 3

Sync module - maintains synchronization of notification appliance circuit).

Enables Temporal Code 3 signal generation output.

1, 2

This mode will accept a steady or a pulsing input.

A steady output signal will be generated.

1, 2, 3

This mode will accept steady or pulsing input.

Sync Mode Selection Table:

Switch Positions

Descriptions

OFF

This mode is designed to work with the Amseco series of horns, strobes,

and horn/strobes to provide a means of synchronizing the Temporal-

1, 3,

coded horns, synchronizing the flash timing of the strobe, allowing

audible notification appliances (horns) and visual notification appliances

(strobes) to be silenced/deactivated at the same time.

This mode is designed to work with the Gentex

and horn/strobes to provide a means of synchronizing the Temporal-

1, 2,

coded horns, synchronizing the flash timing of the strobe, allowing

3, 4

audible notification appliances (horns) and visual notification appliances

(strobes) to be silenced/deactivated at the same time.

This mode is designed to work with the System Sensor

strobes, and horn/strobes to provide a means of synchronizing the

1, 2, 4

Temporal-coded horns, synchronizing the one-second flash timing of the

strobe, allowing audible notification appliances (horns) and visual notifica-

tion appliances (strobes) to be silenced/deactivated at the same time.

This mode is designed to work with the CooperWheelock

horns, strobes, and horn/strobes to provide a means of synchronizing the

2, 3, 4

Temporal-coded horns, synchronizing the one-second flash timing of the

strobe, allowing audible notification appliances (horns) and visual notifica-

tion appliances (strobes) to be silenced/deactivated at the same time.

AL842LGK Board

Output DIP Switches

INPUT SELECT

TEMPORAL

STROBE SYNC

IN>OUT SYNC

series of horns, strobes,

series of horns,

series of

42 ULADA Application Guide