ALTUS APS-3 Schnellstart-Handbuch - Seite 2
Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Empfänger ALTUS APS-3 herunter. ALTUS APS-3 2 Seiten. Positioning systems
Auch für ALTUS APS-3: Schnellstart-Handbuch (8 seiten), Schnellstart-Handbuch (8 seiten)
Seite druckenAPS-3 Battery Removal, Charge and Installation
Complete the following steps for removal, charge and
installation of APS-3 batteries.
One fully charged battery can be used up to 5
hours.
Check which battery is "in use" before removal. See battery
status in SurvCE to replace idle battery. Instructions located in
Power or Battery Status Indicator section of this manuscript.
Press release button to open battery
compartment door (FRONT)
To Replace battery. Pull the battery out or
push to release the battery to slide out and
close the compartment door
To charge battery. Plug the AC wall battery
charger into the wall socket and power LED
turns ON
Place APS-3 battery in charger for 2 hours
or until LED turns GREEN for full charge. RED
LED indicates battery not fully charged.
To load battery in APS-3. Slide the batteries
in the slot and close compartment door.
Check battery status in SurvCE.
SIM Card
Follow the steps below to verify that the GSM/GPRS Modem
works correctly with your activated SIM Card.
1. Establish communication with APS-3 using SurvCE
2. Select Equip tab and then GPS Rover
3. GPS Rover window comes up and select RTK tab
x
Select Device: Internal GSM and Configure button for
Internal GSM. Select a Provider and Input APN Server
for connection.
Configure SIM card for Internal GSM modem
only once per service provider.
x
Select proper Network connection and Configure.
o
TCP/IP Direct | UDP/IP Direct | NTRIP |
SpiderNet | Direct Dial
x
Select Message Type:
o
CMR | CMR+ | RTCM V2.3 | RTCM V3.0
x
Select Base ID and check box to Send Rover Position to
Network for VRS Network.
x
Select Check button on upper right hand corner
x
Flashing orange RTK LED indicates APS 3 is receiving
corrections
WARNING: Incorrect Provider and APN Server will
result in error.
5
7
Communicating with APS-3
Serial cable communication takes precedence over
Bluetooth®. Remove the serial cable from SER1 port
for Bluetooth to resume.
For Wireless Bluetooth® communications with the APS 3 follow
the steps below with a Controller (Allegro, Archer, etc.). Refer
to APS 3 User Manual for variations in controllers.
Your Controller, with SurvCE, has been preconfigured
for wireless communication with the APS-3
receiver(s).
1. Turn ON the APS-3. The RED LED will turn ON and the
GREEN LED GNSS Satellite starts to blink.
2. Turn ON the Controller and Run SurvCE software.
Register SurvCE at http://www.carlsonsw.com/
3. Go to the Equip tab and select GPS Rover.
4. In the Current Tab, select Manufacturer: Altus and Model:
APS-3
5. In the Comms Tab, select the proper APS-3 unit for
connection. APS-3 _####, where #### is product serial
number located underneath the receiver. Click on
Bluetooth® button in upper right hand corner of screen to
bond with your APS-3.
6. If the APS 3 name is not listed select Configure.
7. Then select Find Receiver, and a Bluetooth® Device search
occurs. Highlight the APS 3 name then select the
Bluetooth® button to bond.
Power or Battery Status Indicator
Use SurvCE to check APS-3 battery status. In Equip Tab, select
GPS Rover or GPS Base Station button.
Questions or Comments
Please contact ALTUS Positioning Systems:
Email:
support@altus ps.com
Web:
http://www.altus ps.com/
Phone: 310.541.8139
6
Click on
button
for APS-3 GNSS
Firmware & Battery
Status details.
Battery information is
not available when
using external power.
8