Custom Shop KUS P3000 Sicherheits- und Betriebsanleitung - Seite 6
Blättern Sie online oder laden Sie pdf Sicherheits- und Betriebsanleitung für Sander Custom Shop KUS P3000 herunter. Custom Shop KUS P3000 7 Seiten. 6” variable speed random orbit dual-action polisher
Seite druckenwill take longer. Applying too much wax may also reduce
the life of the Foam Pad. If the Foam Pad continually comes
off the Backing Pad during use, too much wax may have
been applied.
9. After the wax has been applied to the vehicle's surface,
turn off the tool. Unplug the Power Cord from the
extension cord.
10. Remove the Foam Pad from the Backing Pad and with
your hand and the Foam Pad, apply wax to any hard to
reach areas of the vehicle such as around lights, door
handles, under bumpers, etc.
11. Allow sufficient time for the wax to dry.
12. Place a clean Polishing Bonnet (sold separately)
securely onto the Backing Pad.
CAUTION! Tightly pull the string to secure the Polishing
Sanding instruction
TO PREVENT SERIOUS INJURY: Grip the tool firmly in both hands.
1. Wipe the work surface clean of all dirt and debris,
especially that of previous coarser sanding sessions, which
will scratch the surface of a finer grit sanding session
.
2. Attach the desired grit Sanding Disk (sold separately)
onto the Backing Pad.
3. Make sure that the Switch is in the off-position, then plug
in the tool.
4. To start, grip the tool firmly with both hands and press the
Trigger. Release the Trigger to stop.
5. Wait until the tool has reached full speed, then gently
contact the surface.
WARNING
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Make sure that the Power Switch is in the
off-position and unplug the tool from its electrical outlet before performing any procedure in this section.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Cleaning, maintenance, and lubrication
1. BEFORE EACH USE, inspect the general condition of
the tool. Check for:
• loose hardware,
• misalignment or binding of moving parts,
• damaged cord/electrical wiring,
• cracked or broken parts, and
• any other condition that may affect its safe operation.
2. AFTER USE, wipe external surfaces of tool with clean
Bonnet. Secure the string and keep it out of the way by tying
several knots.
CAUTION!
Start and stop the tool only while it is held firmly
against the surface of the vehicle. Failure to do so may
result in the Bonnet being thrown from the Backing Pad.
13. Start the tool and begin buffing off the dried wax.
14. When as much wax as possible has been removed with
the tool, turn off the tool. Unplug the tool.
15. WARNING! Allow the tool to come to a complete stop
before setting it down.
16. Remove the Polishing Bonnet from Backing Pad. Using
the Polishing Bonnet, remove the wax from all hard to
reach areas of the vehicle.
17. Clean, then store the tool indoors out of children's
reach.
6. Keep heavy pressure off of the tool when operating. Allow
the tool to do the work.
7. Move the tool in a uniform pattern up and down or side to
side while sanding to ensure even sanding.
8. Periodically, stop the tool and check for disc wear.
Replace worn sanding discs as needed.
9. TO PREVENT ACCIDENTS, AFTER USE: Turn off the
tool. WARNING! Allow the tool to come to a complete
stop before setting it down. Unplug the tool. Clean, then
store the tool indoors out of children's reach.
cloth.
3. Periodically, wear ANSI-approved safety goggles and
NIOSH-approved breathing protection and blow dust and
grit out of the motor vents using dry compressed air.
4. WARNING! If the supply cord of this power tool is
damaged, it must be replaced only by a qualified
service technician.
5