DKS 8040 microplus Benutzerhandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Empfänger DKS 8040 microplus herunter. DKS 8040 microplus 4 Seiten. Rf receiver (weigand)
Auch für DKS 8040 microplus: Benutzerhandbuch (3 seiten)

Seite drucken

How Receiver Functions

The 8040 receiver responds to the MicroPLUS

Code" that is defined by "Transmitter Button Codes" and "Facility Codes". For

example: an 8040 receiver can be programmed to respond to only the first button on a

multiple button MicroPLUS

receiver can be programmed to respond to only the second button of the same

multiple button MicroPLUS

receivers without fear of both receivers responding to the same transmitter code.

In Weigand output mode, you have the option of having the receiver match or

ignore the facility code to allow the receiver to activate. One receiver can be

programmed to respond to a specific facility code while another receiver can be

programmed for a different facility code.

Programming Selector's 12 functions:

1. Learn Transmitters

2. 26-bit Weigand Programming (Factory Set)

3. 31-bit Weigand Programming

4. 30-bit Weigand Programming

5. Match Facility Code

6. Ignore Facility Code (Factory Set)

B. Set Receiver to MicroPLUS

The receiver comes from the factory already set in the MicroPLUS

mode, follow the steps below.

EXISTING MEMORY that has been previously programmed in the receiver.

1. Turn the Programming Selector to Position B.

2. Press and hold Program Button until the Program LED flashes ONCE and receiver will BEEP once. Press and hold button again, LED will flash

and receiver will beep. Press and hold button a third time until LED continually flashes and beeps.

3. The receiver now needs to have its power turned OFF, then back ON. Receiver is now in MicroPLUS

Press and

2 Sec.

Hold Program

Button

START

Verify Receiver is in MicroPLUS

After power has been turned back ON to receiver. Receiver will emit 3-flashes and beeps, this indicates MicroPLUS

a long flash and beep ONLY if existing memory has been erased from the receiver.

power has been

turned back ON

C. Set Receiver to MicroCLIK

If you need to change the receiver from MicroPLUS

receiver from MicroPLUS

to MicroCLIK™ mode will erase ALL EXISTING MEMORY that has been previously programmed in the receiver.

1. Turn the Programming Selector to Position C.

2. Press and hold Program Button until the Program LED flashes ONCE and receiver will BEEP once. Press and hold button again, LED will flash

and receiver will beep. Press and hold button a third time until LED continually flashes and beeps.

3. The receiver now needs to have its power turned OFF, then back ON. Receiver is now in MicroCLIK™ mode.

Press and

2 Sec.

Hold Program

Button

START

Verify Receiver is in MicroCLIK™ mode:

After power has been turned back ON to receiver. Receiver will emit 2-flashes and beeps, this indicates MicroCLIK™ mode. Receiver may then emit

a long flash and beep ONLY if existing memory has been erased from the receiver.

or MicroCLIK™ transmitter's "Transmitter

or MicroCLIK™ transmitter while a second 8040

or MicroCLIK™ transmitter. Thus allowing a single

or MicroCLIK™ transmitter to activate two different

CAUTION:

Changing an existing programmed receiver from MicroCLIK™ to MicroPLUS

Press and

Release

Hold Program

Button

Beep

mode:

After

Beep

MicroPLUS

to MicroCLIK™ mode, follow the steps below.

Press and

Release

Hold Program

Button

Beep

After

power has been

turned back ON

Beep

MicroCLIK™ mode

7. Learn Master Transmitters (Up to 4)

8. Low Power Mode

9. Normal Power Mode (Factory Set)

A. Erase ALL Memory

B. Set Receiver to MicroPLUS

C. Set Receiver to MicroCLIK™ Mode

D-F. Not Used

Mode (Factory Set)

mode. If you need to change the receiver from MicroCLIK™ to MicroPLUS

2 Sec.

Release

Button

Beep

If receiver has

existing

Beep

programming in

mode

its memory

™

Mode

2 Sec.

Release

Button

Beep

If receiver has

existing

Beep

programming in

its memory

Mode (Factory Set)

mode.

Press and

2 Sec.

Hold Program

Button

Beep

mode. Receiver may then emit

ALL Existing

Memory has

Long

been ERASED

Beep

CAUTION:

Changing an existing programmed

Press and

2 Sec.

Hold Program

Button

Beep

ALL Existing

Memory has

Long

been ERASED

Beep

Program

Selector

Program Button

Program LED: Will flash

sequences during

programming and

flashes during normal

operation or frequency

interference.

Weigand LED's: Will blink

as Weigand data is being

transmitted.

mode will erase ALL

Receiver

Release

power MUST be

Button

turned OFF

then back ON

FINISH

Receiver

Release

power MUST be

Button

turned OFF

then back ON

FINISH